Fama TS 12 Manuel D'utilisation page 36

FREQUENCY PERSONNEL
At the end of every
shift work and
however before the
daily use
PRODUCTS IDENTIFICATION TABLE WITH MINCER GROUP IN ALUMINUM OR IN CAST IRON
ALUMINUM / CAST
MOD IRON
(Codes)
FTS106
FTS106U
TS12
FTS107
FTS107U
FTI106
FTI106U
TI12
FTI107
FTI107U
FTS116
FTS116U
FTS116UT
TS22
FTS117
FTS117U
FTS117UT
Operator All the surface and the machine parts destined to come in contact with the food product or with
the food zones (hopper internal surface, machine neck and the grinding group, the pestle) and the
jets zones (machine external surface) must be cleaned and disinfected with the under reported
modalities. For the grinding group disassembly activities see the previous descriptions.
Scrape the surfaces from the possible food product residuals (for example with plastic
scrapers);
Clean all the food zone surfaces and jets zone with soft dampened clothes (not draining)
with detergent diluted in hot water (also common soap for dishes is good). Don't soak
them. With a towel clean inside the grinding mouth. Use specific products for steel,or for the
aluminum: which must be liquids (not in cream or pastries however abrasive) and above all
must not contain chlorine. Against the fat substances the denatured alcohol.
Rinse with cleaned hot water and successively dry all food zone surfaces and jets zone
with soft clothes that don't lose coats.
Only the STAINLESS steel parts of the mincer group can be washed also in dishwasher, while
the aluminum ones or in cast iron showed in the following table, cannot be washed in
dishwasher.
The grinding group re assembly must happen only after a working requirement, leave the
pieces wrapped in a dry soft clothes that doesn't lose coats.
DISINFECTION
Use detergents with PH neutral not oxidizing
If the hot water is used (> 60°C) use exclusively demineralised water.
If other products are used, these ones must be adequate to the material type.
For the machines with aluminium parts or in cast iron (see following table) it is possible to use
peracetic acid products.
PERIODS OF LONG INACTIVITY
During the machine long inactivity periods provide to pass vigorously on all steel surfaces
(especially if stainless) a clothes soaked of Vaseline oil so that to spread a protective veil.
THINGS NOT TO DO BEFORE OR WHILE CLEANING:
Enter towards the moving elements without to be previously checked of their stop;
Enter towards the moving elements without have stopped it in safety stop (blockage in zero
position of the electric feeding sectioning devices)
PRODUCTS NOT TO USE:
Compressed air with jets towards the zones with flour warehouses and in general towards the
machine;
Vapor equipment;
Detergent that contains CLORO (also if diluted) or its compounds as: the bleach, the muriatic
acid, products to clear the drain, caustic soda products for the marble cleaning, in general
decalcifying, etc ... can attack the steel composition, staining and oxidizing it unavoidable.
The only above described products fumes can oxidize and in any case corrode the steel;
Steel wool, brushes or abrasive discs produced with other metals or alloys (ex. Common steel,
aluminum, brass, etc...) or tools that have previously cleaned other metals or alloys, that
except to scratch the surface.
Detergents in abrasive dust;
Fuel, solvents or inflammable and/or corrosive fluids;
Substances used to clean the silver.
MOD
TI22
TS32
ECO
TI32
ECO
TI12R
MODALITY
ALUMINUM / CAST
IRON
(Codes)
FTI116
FTI116U
FTI116UT
FTI117
FTI117U
FTI117UT
FTS146
FTS147
FTI146
FTI147
FTI106R
FTI106RU
FTI107R
FTI107RU
ORIGINAL INSTRUCTIONS TRANSLATION
ALUMINUM / CAST
MOD IRON
(Codes)
FTI116R
FTI116RU
FTI116RUT
TI22R
FTI117R
FTI117RU
FTI117RUT
Pag.
16
di
18