Stack ST3505 Instructions D'installation page 2

Pro Control High Warning Set Point
To adjust the high warning set point, press and release the WARN button. The warning light will begin to flash and the pointer will move to
the previous high warning set point signifying that warning set mode has been selected. Once in set mode, press the WARN button to move
the pointer down, or press the PEAK button to move the pointer up. Three seconds after the last button press, the warning light will stop
flashingand the pointer will return to the current reading. The warning set points are retained when power is removed from the gauge.
Pro Control High Over Warn Set Point
To adjust the high over warn set point, press and hold the WARN button. After three seconds the warning light will begin to flash and the pointer
will move to the previous high over warning set point signifying that over warn set mode has been selected. Release the warn button. Once in
set mode, press the WARN button to move the pointer down, or press the PEAK button to move the pointer up. Three seconds after the last
button press, the warning light will stop flashing and the pointer will return to the current reading. The over warn set points are retained when
power is removed from the gauge.
Pro Control Low Warning Set Point
To adjust the low warning set point, press and hold the WARN button, and while still holding the WARN button, press and release the PEAK
button. The warning light will begin to flash and the pointer will move to the previous low warning set point signifying that warning set mode has
been selected. Once in set mode, press the WARN button to move the pointer down, or press the PEAK button to move the pointer up. Three
seconds after the last button press, the warning light will stop flashing and the pointer will return to the current reading. The warning set points
are retained when power is removed from the gauge.
Pro Control Low Over Warn Set Point
To adjust the low over warn set point, press and hold the WARN button, and while still holding the WARN button, immediately press and hold
the PEAK button. After three seconds the warning light will begin to flash and the pointer will move to the previous low over warning set point
signifying that over warn set mode has been selected. Release both buttons. Once in set mode, press the WARN button to move the pointer
down, or press the PEAK button to move the pointer up. Three seconds after the last button press, the warning light will stop flashing and the
pointer will return to the current reading. The over warn set points are retained when power is removed from the gauge.
Change Backlight Color
To change the backlight color:
With power off, press and hold the warning button. Apply power to the gauge. Release the WARN button. Press and release the PEAK button.
The pointer will move to half scale and the dial will illuminate with the current Backlight Color. Press and hold the PEAK button to cycle through
the available colors. Once you have selected the desired color, release PEAK and don't press any buttons for about three seconds. The dial
will flicker white several times to indicate the desired setting has been saved and the gauge will return to normal operation with your new color
selection. Color selections are saved when power is off.
Change Low Warn Color
(Region A color)
Warn Color Set Mode:
With power off, press and hold the WARN button. Apply power to the gauge. Release the WARN button. The pointer will be at the stop pin and
the dial illumination will be off. Press and release the WARN button to cycle between HIGH warn color set and LOW warn color set modes. In
High Warn color set mode, the pointer will move to full scale and the dial will illuminate with the current High Warn color. In Low Warn color set
mode, the pointer moves to the minimum position and the dial will illuminate with the current Low Warn color.
To change Low Warn Color:
When the Low Warn color set mode has been selected (see above), press and HOLD the WARN button to cycle through the available colors.
Once you have selected the desired color, release the WARN button. Don't press any buttons for about three seconds. The dial will flicker
white several times to indicate the desired setting has been saved and the gauge will return to normal operation with your new Low Warn color
selection. Color selections are saved when power is off.
Change High Warn Color
(Region C color)
Warn Color Set Mode:
With power off, press and hold the WARN button. Apply power to the gauge. Release the WARN button. The pointer will be at the stop pin and
the dial illumination will be off. Press and release the WARN button to cycle between HIGH warn color set and LOW warn color set modes. In
High warn color set mode, the pointer will move to full scale and the dial will illuminate with the current High Warn color. In Low Warn color set
mode, the pointer moves to the minimum position and the dial will illuminate with the current Low Warn color.
To change High Warn Color:
When the High Warn color set mode has been selected (see above), press and hold the WARN button to cycle through the available colors.
Once you have selected the desired color, release the WARN button. Don't press any buttons for about three seconds. The dial will flicker
white several times to indicate the desired setting has been saved and the gauge will return to normal operation with your new High Warn color
selection. Color selections are saved when power is off.