Configuration - Cardin Elettronica ZVL322.02 Mode D'emploi

PROGRAMMING THE TORQUE
horised copying or use of the information contained in this document is punishable by law
Display
indications percentage
P1
P2
P3
PROGRAMMAZIONE FIG9-9a
Description :
: DM0299
PRG811-FIG.9-9a
P4
PRG811
Date :
25-06-97
P5
NICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Work time programming
Description : PROGRAMMAZIONE FIG9-9a
:
DM0299
PRG811-FIG.9-9a
PRG811
Date : 25-06-97
NICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Press PROG
first
second
third
fourth
fifth
Description : PROGRAMMAZIONE FIG11
Programming is carried out step by step by the system which activates the motors according to the
PRG811-FIG.11
settings carried out in the previous step (eg.: If you have chosen a 1 gate configuration, only motor
25-06-97
number 1 will be activated ).
- 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
As you can see the programming method requires you to press the PROG button according to the
type of gate and the number of leaves.
If the electric locking device, preflashing and gate jolt (initial movement in the closing direction) have
been enabled, they must also be set during programming.
Note 1: the maximum work time and pause time duration is 300 seconds: once this time limit has
been reached the programmer will automatically move on to the next programming stage
(memorizing the maximum time). The maximum closing direction delay time for gate 1 is
equal to the work time of gate 2.
Note 2: If the gate jolt has been enabled you cannot disable the electric locking device.
Selecting a single gate (gate 1) automatically disables the travel limits for gate 2.
Selecting a sliding gate automatically disables the gate jolt.
Excluding travel limits during programming means you will not have to bridge the contacts
on the terminal board.
9a
9
9a
9
Torque
Voltage
40% 110Vac
55% 135Vac
65% 155Vac
75% 185Vac
100% 230Vac
The start of the work time programming stage is indicated on the display by the letter
11
"t" which remains for about 2 seconds after which the display will switch off.
At this point only the PROG button is enabled. Each time the button is pressed
the time programming will proceed as indicated below:
Gate 1
open gate 1
start pause
end pause -> close
gate 1
-
Pressing the PROG at the point described in fig. 8 will allow
you to set the torque limiter. The values range from 1 to 5, and
the value shown in the figure is relative to the minimum torque
(the characters "P" and "1" will alternate on the display).
Each time the SEL button is pressed the value will increase
by 1; once you arrive at "5" the next time you press SEL the
display will show the symbol , pressing SEL again will cycle
back to "1" (see appendix 1). The indication on the display
will be alternating if a value has not been selected and will be
fixed when you arrive at a previously selected value.Pressing
the PROG button will set the value on the display: to change
this value press SEL, and then press PROG again.
When the symbol appears on the display after 20 seconds
the programmer will save the parameters set up to now and
leave the programming mode. If you press the PROG button
during this period you will move on to the last programming
stage (work time setting).

CONFIGURATION

2-leaf sliding gate
open gates 1 and 2
block gate 1
block gate 2
start pause
close gates 1 and 2
-
17
2-leaf hinged gate
open gate 1-delay
fixed for gate 2 (2 sec)
block gate 1
block gate 2
start pause
end pause-close gate 2
end closing direction delay
close gate 1