Cardin Elettronica ZVL322.02 Mode D'emploi page 16

horised copying or use of the information contained in this document is punishable by law
PROGRAMMING PROCEDURE (see appendix 1, page 21)
1
sed copying or use of the information contained in this document is punishable by law
2
rised copying or use of the information contained in this document is punishable by law
3
orised copying or use of the information contained in this document is punishable by law
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
4
Description : PROGRAMMAZIONE PRG 811 (fig1)
PRG811-FIG.1
06-97
020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
authorised copying or use of the information contained in this document is punishable by law
5
Description : PROGRAMMAZIONE FIG2
92
PRG811-FIG.2
: 25-06-97
.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
PROGRAMMAZIONE FIG3
Description :
6
PRG811-FIG.3
25-06-97
- 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Description : PROGRAMMAZIONE FIG4
8
PRG811-FIG.4
06-97
020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Description : PROGRAMMAZIONE FIG5
PRG811-FIG.5
- pressing the SEL button moves you back to step "1".
-06-97
31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
- pressing the PROG button moves you to the next stage.
DISPLAY
1
Description : PROGRAMMAZIONE FIG6
2
PRG811-FIG.6
Description :
Drawing number : DM0297
3
PRG811-FIG.7
5-06-97 Product Code : PRG811
4
31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft : P.J.Heath Date : 25-06-97
5
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
6
7
8
9
Description : PROGRAMMAZIONE FIG8
298
PRG811-FIG.8
1
0
e :
25-06-97
A
p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
b
* Travel direction inversion is active only during closing.
no commands will be received when the FTCI are in alarm and the programmer is in block, not even during opening.
**
*** flashes slowly during opening, quickly during closing, remains lit when the gate is blocked in an open position and is off when the gate
is completely closed.
Before commencing make sure that the gate is closed: the LED display will be off. To select the
manual operation mode the jumper "J1" must be open.
Keep the PROG button held down for more than 4 seconds: The letter "d" will appear on display
DS1 (this is the parameter definition mode).
After about 1 second the programming steps starting from step 1 will appear on the display.
If this is the first time the system has been programmed (EEPROM memory empty) none of the
parameters will have been set, meaning that the numbers will flash at each step; if programming
is being carried out on a system which has already been programmed, the flashing will depend
on the value read from the EEPROM when the system was switched on (you may therefore check
the previously set parameters). Press the PROG button
As you can see in figures 4-5, pressing the PROG button when the display is not flashing will
force the number to flash. This operation can be repeated as many times as required until the
desired setting has been obtained.
Pressing the SEL button moves on to the next programming stage. It is not
7
possible to return to the previous programming stage, in fact you must carry
on until the last stage has been reached before the cyclical programming cycle
will allow you to return to stage 1 (see appendix 1). Note.: While SEL is pressed
LED LD8 will remain lit
After the tenth stage, shown by the number "0", the next time you press the SEL button will move
you on to the stage shown in figure 8, which indicates the separation between the configuration
of the system and the torque limiter/work time programming. At this point there are three pos-
sibilities (see appendix 1):
- after 20 seconds of inactivity (without pressing any buttons) the programmer will save the
parameters set up to now and exit the programming mode.
FIXED
Single gate
Hinged gates
PROGRAMMAZIONE FIG7
Gate opening jolt enabled
Electric locking device enabled
Dynamic button open-close*
Automatic reclosing enabled
Preflashing enabled
Gate 1 travel limit enabled
Gate 2 travel limit enabled
Warning lights flash continuously
FTCI active even when in blocked **
Non intermittent indicator light
Gate opening jolt disabled
Electric locking device disabled
Dynamic button open-block-close-block
Automatic reclosing disabled
Gate 1 travel limit disabled
Gate 2 travel limit disabled
Warning lights flash intermittently
FTCI active only during closing
Intermittent indicator light***
16
FLASHING
Double gate
Sliding
Preflashing disabled