Technical Data - Niko 7801 Serie Mode D'emploi

XXX-7801X
Automatic and unwanted The motion detector switches on
switching after the mains voltage has been
interrupted.
Sunlight falls on the lens or in the
detection area.
Heat/cold penetrates through to
the detection area by way of an
open door or window.

6. TECHNICAL DATA

dimensions
power supply voltage
mounting
connection terminals
no-load power consumption
relay contact
maximum switching capacity
maximum switching current
detection angle
detection range
switch-off delay
light sensitivity
mounting height
ambient temperature
protection degree
functionality
180°
8-9 m 0
7. WARNINGS REGARDING INSTALLATION
- The installation should be carried out by a registered installer and in compliance with the statutory regulations.
- This manual should be presented to the user. It should be included in the electrical installation file, and it
should be passed on to any new owners. Additional copies are available on the Niko website or via the Niko
support service. The latest manual for this product is available on the Niko website at any time.
- During installation, the following should be taken into account (non-exhaustive list):
- the statutory laws, standards and regulations.
- the technology currently available at the time of installation.
- this manual, which only states general regulations and should therefore be read within the scope of
each specific installation.
- the rules of proper workmanship.
This product complies with all of the relevant European guidelines and regulations. If applicable, you can find
the EC declaration of conformity regarding this product at www.niko.eu.
8. NIKO SUPPORT
In case of doubt or for the specific exchange procedure in case of a possible defect, contact the Niko support
service in Belgium at +32 3 778 90 80 or your wholesaler/installer. Contact details and more information can
be found at www.niko.eu under the "Help and advice" section.
9. GUARANTEE PROVISIONS
- The period of guarantee is four years from the date of delivery. The delivery date is the invoice date of purchase
of the product by the consumer. If there is no invoice, the date of production applies.
- The consumer is obliged to inform Niko in writing about the non-conformity, within two months after stating
the defect.
- In case of a non-conformity, the consumer only has the right to a product repair or replacement free of charge,
which shall be decided by Niko.
- Niko shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless
use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance
instructions or an external cause, such as damage due to moisture or overvoltage.
10
- The compulsory regulations of the national legislation concerning the sale of consumer goods and the
protection of the consumer in the countries where Niko sells, directly or via sister companies, subsidiaries,
chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned
rules and regulations.
nv Niko sa
SK
The lighting is illuminated for
90 seconds before the
interruption. After that, the device
is in automatic mode.
Set the lux value to twilight.
Close the door or window or
move the device.
base: 31 mm (D)
motion detector: 30 mm (D)
230 Vac ± 10%
flush-mounting box with flush-mounting depth of min.
40 mm
5 (maximum capacity per connection terminal:
1 x 2.5 mm²)
< 0.5 W
max. 10 A, 250 Vac, light- and motion-sensitive
140 µF
165 A/20 ms
horizontal: 180° – vertical: 60°
(see illustrations below)
8 – 9 m
± 1 – 30 min
± 10 – 1000 lux
0.8 – 1.2 m
-5 – +45°C
IP40
may be used as master or as slave
0.8 - 1.2 m
0 m
50°
8-9 m
Industriepark West 40, BE-9100 Sint-Niklaas, Belgium — tel. +32 3 778 90 00 — fax +32 3 777 71 20 — e-mail: support@niko.be — www.niko.eu
Pred inštaláciou a spustením systému si prečítajte celý návod. Návod uschovajte pre budúce použitie.
1. POPIS
180° detektor pohybu so zapustenou montážou je elektronický spínač detekcie pohybu, ktorý je určený
len na použitie v interiéri. Detektor pohybu zapne záťaž (osvetlenie), ak sa zistí pohyb zdroja tepla a ak je
intenzita denného svetla nižšia ako nastavená hodnota luxov. Zariadenie deteguje pohyb pomocou pasívneho
infračerveného snímača (PIR).
Zariadenie (aktivátor + snímač) je dodávané na predmontovanom kovovom prístrojovom spodku (45 x 45).
Rámček je potrebné objednať samostatne.
2. INŠTALÁCIA
2.1. Zapojenie
Nebezpečenstvo: Pred inštaláciou detektora pohybu odpojte všetky zdroje energie. Nepripájajte zariadenie k
napájaciemu zdroju až do dokončenia inštalácie (vrátane rámčeka).
A. Jeden svetelný okruh s jedným detekčným bodom
Pripojte detektor pohybu a záťaž podľa nasledujúcej schémy:
L
230 Vac
N
B. Jeden svetelný okruh s viacerými detekčnými bodmi
V tomto prípade musí byť priradený master a slave. K jednému detektoru master môžete priradiť najviac
osem detektorov slave.
Pripojte slave k master podľa schémy nižšie:
L
230 Vac
N
Slave
10°
0°
C. Použitie externého tlačidla alebo spínača
Ak sa má dať zariadenie ovládať aj ručne, k detektoru pohybu pripojte externé tlačidlo alebo spínač. Tlačidlo
alebo spínač môžete pripojiť buď k master alebo slave.
Pre pripojenie tlačidla alebo spínača postupujte podľa nižšie uvedenej schémy:
L
230 Vac
N
2.2. Montáž
Tip: Neinštalujte detektor pohybu na plochu s priamym slnečným svetlom ani v blízkosti zdrojov tepla alebo
vzdušných prúdov (ventilácia alebo klimatizácia). Môže to zbytočne aktivovať detektor pohybu.
Tip: Namontujte detektor pohybu (master) na miesto, kde sa dá intenzita svetla čo najlepšie merať (hodnota v luxoch).
Pripevnite detektor pohybu do montážnej krabice s hĺbkou zapustenia 40 mm vo výške od 0,8 do 1,2 m.
3. NASTAVENIA
Pod odklápacím krytom na prednej strane detektora pohybu sú dva potenciometre na nastavenie nasledovných
štyri parametrov:
svetelná citlivosť (± 10 – 1000 lux)
1
doba oneskorenia vypnutia (± 1 – 30 min.)
2
slave
3
testovací režim
4
1
3
Master
2
4
PMXXX-7801XR14325