STEINEL PROFESSIONAL HBS 300 Highbay Mode D'emploi page 10

HBS 300 Highbay / HBS 200 Highbay stay-ON time
ON
Low
1 2 3 4
DIP swich for setting HBS 300 Highbay / HBS 200 Highbay stay-ON time Time Delay DIP Switch
1 2 3 4
ON ON ON OFF
ON OFF OFF OFF
OFF ON ON OFF
ON OFF ON OFF
ON ON OFF OFF
OFF ON OFF OFF
OFF OFF ON OFF
OFF OFF OFF OFF
N/A N/A N/A ON
Low
Setting and starting up HBS 300 Highbay / HBS 200 Highbay
Lens covers
Lens covers can be used to adjust the high bay
sensor's coverage as needed.
LC4 shroud for reducing LC5 180° half-moon lens cover for
HBS 300 Highbay reach HBS 300 Highbay
LC4
10
20
10
30
20
40
30
40
30 ft 30 ft
22 ft 22 ft
Stay-ON time is the period of time lights remain
ON after detecting the last movement. This time
can be set from 15 sec. to 30 min. Factory set-
High
ting is 15 min.
After setup and commissioning tests are
Time Time
complete, adjust the stay-ON time and light
15 sec level settings to fit the application needs.
1 min
5 min
10 min
15 min
20 min
25 min
30 min
High
Manual
override
override
The plastic shrouds simply push on to the front
of the HBS 300 Highbay or HBS 200 Highbay.
LC1 aisle start cover for
LC5
HBS 200 Highbay
LC1
10
20
30
35 ft 40 50 40
22 ft
- 18 -
Wireless interconnection by means of optional MF1 wireless module
An MF1 wireless group control module with
wireless group control capability can be added
to any HBS 300 Highbay or HBS 200 Highbay
sensor.
MF1 safety precautions / installation
Please only plug the module in with the mains
n
power supply switched OFF. (see Fig.)
Only use genuine replacement parts.
n
Technology
868 MHz, bidirectional. Reach up to 100 m,
depending on the line of vision, walls, wall pro-
jections, corridor corners, wall reflections etc.
RM 50 Highbay wireless receiver
The optional wireless receiver extends lighting
control within a group of luminaires, making it
Wireless communication
STEINEL wireless lighting controllers are
4
grouped together through a DIP switch address.
When a wireless presence sensor in the group
detects a movement, all devices in that group
will be switched ON. For example, when a
sensor detects the presence of a person and
switches the light ON, this switching command
Setting and starting up RM 50 Highbay (MF1)
Groups
50 ft
53 ft
Stay-ON time is at least 30 sec. when using the
MF 1.
EAN MF1 .................................. 4007841736712
The wireless module must not be plugged in
n
when using the Install mode.
Recommendation: reliable wireless link up to
30 m is ideal.
the ideal accessory for intelligently intercon-
necting high-bay sensors.
will be sent to all wireless devices in this group.
All these devices then switch the light ON. Light
only switches OFF when command signals stop
being sent to the group and the last device's
stay-ON time has elapsed. The switching sig-
nals are limited by the devices' wireless reach.
1 2 3 4 5
1 2 3 4 5
The 5 position DIP switch on all STEINEL wire-
less devices can be used for setting 32 different
addresses or groups.
All devices in a group must have the same DIP
switch setting. The ON switching commands
only apply within a group.
- 19 -
5