Cleco CV-375 Serie Manuel Produit page 2

EN
The original language of this manual is English.
Product Safety Information:
Intended Use:
These air impact wrenches are driven by compressed
air to assemble or remove threaded fasteners.
For additional product safety information refer to Apex
Tool Group, LLC or Apex Tool Group GmbH & Co. OHG
document GS-2000, General Safety Air Assembly Tools.
WARNING
This impact wrench must not be modified in any manner
unless approved in writing by Apex Tool Group, LLC or
Apex Tool Group GmbH & Co. OHG. All safety devices
must be properly installed and maintained in good
working order. Abuse, misuse, or failure to obey this and
any other issued warnings may result if injury or death.
EC Declaration of Conformity:
We affirm that this machine is in accordance with
the following EC regulations (2006/42/EC). Applied
harmonized standards are ISO 12100:2010.
The name, job function and address of the person
authorized to compile the technical file.
Mr. Vishnu Irigireddy
Director of Global R&D- Mechanical Engineering
Apex Tool Group
670 Industrial Drive
Lexington, SC 29072
_______________________
Signature: Vishnu Irigireddy
Date: April 21, 2014
Noise and Vibration:
Air Line Lubrication:
Sound Level dB(A)
(ISO15744)
Model
† Pressure ‡ Power
(L )
p
Refer to the specification table in the back of this manual
for individual model sound level and vibration values.
† K = 3dB measurement uncertainty
pA
‡ Kw = 3dB measurement uncertainty
A
* K = Vibration measurement uncertainty
Use Apex Tool Group, LLC or Apex Tool Group GmbH
& Co. OHG's lightweight air tool oil 500021 (available
in quantities shown in the following chart) or an SAE-5
lightweight spindle oil.
Product Information
Vibration m/s 2
(ISO28927)
Level *K
(L )
w
Cleco
®
Part No.
540397 1 Quart (0.94 liter)
533485 1 US Gallon (3.78 liter)
Air Supply Line:
Parameter
Air Hose
Working
pressure range
Compressed air
Power or speed regulation system:
Models that include a Power Regulation System allows
the operator to select desired relative output power or
speed. To regulate the power, adjust this system to the
desired level as indicated on the tool. It is recommended
that if this feature is needed, that you adjust to the
lowest power setting and gradually advance towards the
maximum setting, as needed. The indicators marked on
the tool are for reference ONLY and DO NOT indicate
specific levels of power. Many parameters will affect
the ultimate power output, including but not limited to:
supplied air pressure, quality, volume, dimension of air
hose, actuation time of tool, pressure applied to throttle,
joint specifications, etc. Calibrate the system, including
the tool, to the desired output level.
Service and Repair:
Tool service and repair should be performed by an
authorized Apex Tool Group, LLC or Apex Tool Group
GmbH & Co. OHG Center. Refer to the last page of this
manual for locations.
Disposal:
Observe local disposal guidelines for all
components of this tool and its packaging.
Copyright Protection:
Apex Tool Group, LLC or Apex Tool Group GmbH &
Co. OHG reserves the right to modify, supplement or
improve this document or the product without prior
notice. This document may not be reproduced in any
way, shape or form, in full or parts thereof, or copied to
another natural or machine readable language or to a
data carrier, whether electronic, mechanical, optical or
otherwise without the express permission of Apex Tool
Group, LLC or Apex Tool Group GmbH & Co. OHG
Page 2
Packaged Designation
Airlube 10W/NR-420LB DR
Airlube 10W/NR-420LB DR
Description
Minimum inside diameter: 3/8" (9.55mm)
Maximum length: 8.0' (2.4 m)
Performance rated at: 90 psi (620 kPa)
Air quality according to ISO 8573-1, quality
class 2.4.3
The compressed air must be clean and dry.
PL12-1081
06/25/2015