Dyson DC17 Guide D'utilisation page 8

ASSEMblY
• Stand the vacuum cleaner up straight and slide the hose into guides at the back
of the vacuum cleaner and click into place.
• Ensure the hose is straight and slide the wand straight down into the hose until it
clicks into place.
• Click the wand handle into the top of the vacuum cleaner.
• Attach the tools to the vacuum cleaner and wind the cable anti-clockwise around
cable hooks and secure with clip.
USINg YOUR dYSON vACUUM
Unwind the cable and insert the plug into a suitable socket.
Hold the cleaner head down with your foot and pull the handle downwards.
To switch 'ON' or 'OFF' press the power button in front of the handle.
CAUTION:
• Do not use or store this machine below 32°F (0°C). Ensure that the vacuum is at
room temperature before operating.
• Do not allow the vacuum to be used by anyone who may not be able to operate
it safely.
• The use of an extension cord is not recommended.
• Always switch off and unplug the vacuum before performing maintenance on
your vacuum.
• Ensure the cyclone is secured to the vacuum. Do not press the cyclone release
button or shake the vacuum while carrying or it could fall and cause injury.
• Store the vacuum indoors. Put the vacuum away after use with the cord coiled
safely, to prevent tripping hazards.
• Do not use outdoors or on wet surfaces or to vacuum water or other liquids –
electric shock could occur.
• Check to ensure your electricity supply corresponds to that shown on the rating
plate, which can be found behind the clear bin. The vacuum must only be used
as rated.
• Do not lubricate any parts, or carry out any maintenance or repair work other
than that shown in this manual, or advised by the Dyson Customer Care
Helpline.
PLEASE NOTE:
• This vacuum is intended for household use only. Fine dust such as plaster dust or
flour should only be vacuumed in very small amounts.
• Do not use the vacuum to pick up sharp hard objects, small toys, pins, paper
clips, etc. They may damage the vacuum.
• Consult your flooring manufacturer's recommended instructions before
vacuuming and caring for your flooring, rugs, and carpet. The brush bar on
the machine can damage certain carpet types and floors. If unsure turn brush
bar off in order to enable proper operation. Some carpets will fuzz if a rotating
brush bar is used when vacuuming. If this happens, we recommend vacuuming
in bare floors mode and consulting with your flooring manufacturer.
• When vacuuming, certain carpets may generate small static charges in the
clear bin or wand. These are entirely harmless and are not associated with the
electricity supply. To minimize any effect from this, do not put your hand or insert
any object into the clear bin unless you have first emptied it and rinsed it out with
cold water. (see 'Clear bin cleaning section').
hARd FlOORS OR CARPETS
The brush bar will always default to 'ON' (spinning) each time you switch on
the vacuum and recline it for cleaning. The brush bar will automatically stop
if it becomes obstructed. If the brush bar stops during use, please refer to the
'Clearing brush bar obstructions' section.
To switch the brush bar 'OFF' (e.g. for hard floors), recline the vacuum and turn
it 'ON', then press the brush bar 'ON/OFF' button – the brush bar will stop
spinning.
hIgh-REACh ClEANINg
CAUTION:
• Switch 'OFF' the vacuum before changing tools.
• Powerful suction can cause the hose to 'pull back' – please take care.
• Take extra care when vacuuming on stairs; do not work with the vacuum above
you on the stairs. Do not put the vacuum on chairs, tables etc.
• Ensure the vacuum is in upright position before using tools.
PLEASE NOTE:
• To release the wand, open the wand cap and pull the red tube until the wand
releases from the vacuum. Tools can be attached to either the hose or wand.
• The brush bar will not rotate when the vacuum is in an upright position.
• Ensure wand cap is closed when not in use.
ClEAR bIN EMPTYINg
CAUTION:
• Switch 'OFF' vacuum and unplug the vacuum before emptying the clear bin.
PLEASE NOTE:
• Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
• To remove the clear bin from the vacuum press the button at rear of cyclone
carrying handle. To release the dirt, press the red clear bin release button.
• Do not use the vacuum without the clear bin in place.
• To minimize dust/allergen contact when emptying, encase base of bin tightly
in a plastic bag before trigger releases dirt. Remove bin carefully and seal bag
tightly, dispose as normal.
8
7/8/09 10:45 AM C30744_DC17_USCA_OPS_MAN_15_4c0s
ClEAR bIN ClEANINg
CAUTION:
• Do not immerse the whole cyclone in water or pour water into the cyclones.
• Ensure the clear bin is completely dry before replacing.
PLEASE NOTE:
• Do not use detergents, polishes or air fresheners to clean the clear bin.
• Clean the shroud with a cloth or dry brush to remove lint and dust.
• Do not put clear bin in a dishwasher.
WAShINg YOUR FIlTER
DO THIS EVERy 6 MONTHS
CAUTION:
• Switch 'OFF' and unplug the vacuum before removing the filter.
• Ensure the filter is completely dry before refitting to the vacuum.
PLEASE NOTE:
• Check your filter regularly and wash at least every 6 months according to
instructions to maintain performance.
• Please leave to dry completely for 24 hours.
• The filter may require more frequent washing if vacuuming fine dust.
• Do not use detergents to clean the filter.
• Do not put the filter in a dishwasher, washing machine, tumble dryer, oven,
microwave or near an open flame.
lOOKINg FOR blOCKAgES
CAUTION:
• Switch 'OFF' and unplug the vacuum before checking for blockages. Failure to
do so could result in personal injury.
• Please ensure vacuum is upright and switched off before removing hose or
airway inspection parts.
• Beware of sharp objects when clearing blockages.
• Refit all parts of the vacuum securely before using.
PLEASE NOTE:
• Clearing blockages is not covered by your vacuum's limited warranty. This
vacuum is fitted with a thermal cut-out. If any part of your vacuum becomes
blocked, it may overheat and then automatically shut off. Switch 'OFF' and
unplug the vacuum and leave to cool down for at least 60 minutes before
attempting to check filter or for blockages. Clear blockage before restarting.
ClEARINg bRUSh bAR ObSTRUCTIONS
CAUTION:
• Switch 'OFF' and unplug the vacuum before clearing brush bar obstructions.
Failure to do so could result in personal injury.
• If any part of your machine becomes blocked, it may overheat and then
automatically shut off. Unplug vacuum and leave to cool down. Clear blockage
before restarting.
• Beware of sharp objects when clearing obstructions.
• Refit all parts of vacuum securely before using.
PLEASE NOTE:
• Clearing the brush bar obstruction is not covered by your vacuum's limited
warranty.