Dimplex Optimyst Serie Instructions De Montage page 14

7. When all products are paired, test the remote control by pressing the
a signal from the remote control you can bring that product back in line with the others via the Manual Controls or
the receiver controls.
GETTING THE DESIRED FLAME EFFECT
1. Switch the appliance on by pressing the main switch to the on position and pressing the
start after 45seconds.
2. Press the and
to the changes you make.
Once you have made your adjustments to both the flame height and crackling sound, the appliance will keep these
settings even if you power off the appliance by either the on/standby button or by the main switch. The next time you
switch on the appliance, it will start up as normal, wait 45 seconds for the flames to start and then revert to the adjusted
settings.
Nozzle Inserts
Nozzle inserts have been supplied and fitted to the nozzle opening. These inserts are used to alter the profile of the
flame effect. These inserts can be removed if a different flame profile is preferred. In addition to these inserts, inserts for
blocking the flame in certain areas have also been supplied. To fit these inserts, remove the exisitng inserts that have
been supplied and fitted to the product. Break the blocking inserts into the required length. Snap the inserts into the
nozzle opening in the desired location. See Fig 22 for further deatils.
LOW WATER / REFILLING THE WATER TANKS
When the water tanks have emptied and the water level in the product is getting low, the product will flash its LEDs twice
and beep twice. The product will operate for a further 15 minutes before beeping once and switching into low water
mode. For products being operated with the LED log fuel bed, the fuel bed will remain illuminated while in low water
mode. At this point, the product can either be switched into stand-by mode using the remote control or Bluetooth receiver
or the product can be refilled with water. Refilling the product with water will cause the product to restart automatically.
To refill the tank, remove the fuel bed and remove the water tank from its position on top of the sump. Refill the water tank
using filtered/decalcified water only. The tank can then be replaced on top of the sump. If the product was not switched
into stand-by mode after experiencing low later, the product will restart automatically after about 20 seconds of refilling.
Please note that for a CAS1000R product, the side of the product that is experiencing low water will flash twice and beep
twice. The water tanks on both sides of the CAS1000R product can be refilled at this point as it is likely that they should
both be empty or near empty.
Maintenance
GENERAL TIPS
Only use filtered/decalcified water in this appliance.
Always ensure that the appliance is sitting on a level surface.
If you intend not using the appliance for longer than 2 weeks, remove and empty the sump and water tank.
Once installed, never move this appliance or lay on its back, without draining the water from sump.
CLEANING
Warning – Always press Switch 'A' to the 'OFF' (0) position (Fig 21) and disconnect from the power supply before
cleaning the fire.
We recommend cleaning the following components once every 2 weeks, particularly in hard water areas:
Sump, Nozzle, Tank cap and seal, Air filter
For general cleaning use a soft clean duster – never use abrasive cleaners.
To remove any accumulation of dust or fluff, the soft brush attachment of a vacuum cleaner should occasionally be used.
Sump
1. Press Switch 'A' to the 'OFF' (0) position (Fig 21)
2. Gently lift off the fuel bed and place it aside.
3. Remove the water tank from its position on top of the sump.
4. Disconnect the electrical connector to the transducers, located on the right side of the sump. (Fig 23).
5. There are two orange clips holding down the nozzle on the sump; one on the left and one on the right hand side of
the nozzle. On the left side, press in the clip with one hand and with the other lift the nozzle out of the clip. Repeat
this for the right side (Fig 24). The nozzle can now be lifted up and placed aside (Fig 25).
6. Gently lift up the sump (Fig 26), taking care to keep it level so as not to spill any water. Sit the sump in the sink.
7. Carefully empty the sump into the sink taking note that the transducer is held in place by a retaining clip.
buttons to adjust the flame to your desired level. Please give the flame generator time to react
button. If any of the products fail to receive
6
button. The flames will