Technical Data - EINHELL ERT 200 Mode D'emploi

GB
the user is responsible for any damage caused
to third persons by use of the trimmer.
Never cross roads or pebble paths with the grass
trimmer switched on. When you are not using the
grass trimmer, keep it in a dry place out of the
reach of children.
Use the grass trimmer only as described in these
directions for use and always hold it vertical to
the ground. All other positions are dangerous.
Check the screws regularly to see that they are
properly tightened. The mains voltage must be
the same as the voltage specified on the rating
plate. Check the power cable regularly for signs
of damage or aging. Never use the grass trimmer
if the power cable is in less than perfect
condition. Power cables used with the trimmer
must not be of a lighter duty class than HO7RN-
F rubber-insulated flexible cables according to
DIN 57282 / VDE 0282 with a minimum diameter
of 1.5 mm 2 . Plug connectors must be equipped
with earthing contacts and the coupling must be
rain-water-protected. Keep cables and other
objects out of the area you want to cut. If you
have to lift the grass trimmer to move it, switch
off the motor and wait for the rotating tool to stop.
Before you leave the trimmer, switch off the
motor and pull out the power plug. Before you
connect the grass trimmer to the power supply,
make sure that none of its moving parts are
damaged and that the line spool is correctly
inserted and fastened. Never cut against hard
objects when using the grass trimmer. This is
imperative to avoid causing injury to the user and
damage to the trimmer. Use only original
replacement parts for repair and maintenance
purposes. Have repairs carried out only by a
qualified electrician. Examine the grass trimmer
for signs of wear or damage each time before
you use it and after any collisions. Have
essential repairs carried out without delay.
Always keep your hands and feet away from the
cutting mechanism, particularly when you switch
on the trimmer. After pulling out new line, always
return the trimmer to normal working position
before you switch it on again. Never use
replacement parts or accessories which are not
foreseen or recommended by the manufacturer.
Pull out the power plug before carrying out any
inspection, cleaning or other work on the trimmer
and whenever it is not being used.
Caution! The nylon line will run on for a few
seconds after the tool is switched off!
12
3. Explanation of the warning notice
(see Figure 2) on the grass trimmer
1: Caution!
2: Wear safety goggles!
3: Protect from the damp!
4: Read the directions for use before putting into
operation for the first time!
5: Pull out the power plug before checking if a
connecting lead is damaged!
6: Keep third parties away from the danger zone!
7: The tool runs on after being switched off!

4. Technical data

ERT 200
Voltage: 230 V ~ 50 Hz 230 V ~ 50 Hz
Power rating: 200 W
Cutting width: 200 mm
Revolutions n0: 13800 min
Nylon cutting line: Ø 1.3mm
Sound pressure level
LPA: 81 dB
Sound power level
LWA: 92 dB
Vibration a
w
Weight: 1.25 kg
Article number: 34.011.20
The noise level of this machine may exceed 85
dB(A). In this case, noise protection measures need
to be introduced for the user. The machine's noise
was measured in accordance with IEC 59 CO 11,
IEC 704, DIN 45635 Part 21, NFS 31-031
(84/538/EEC). The level of vibrations emitted from
the handle is 2,5 m/s
in accordance with ISO 5349.
ERT 250
250 W
200 mm
12400 min
-1
Ø 1.3mm
82 dB
93 dB
2,5 m/s 2 2,5 m/s
1.35 kg
34.013.20
. Measurements were taken
2
-1
2