Technical Data; Fitting The Guard, Handle Skids And Retractable Underarm Support; Proper Use; Before Using For The First Time - EINHELL New Generation RT 527 Mode D'emploi

Anleitung RT 527 SPK 1

4. Technical data

Voltage
Power rating
Cutting width
Speed
Nylon cutting line
Sound pressure level LPA
Sound power level
Vibration aw
Weight
The noise level of this machine may exceed 85
dB(A). In this case, noise protection measures need
to be introduced for the user. The machine's noise
was measured in accordance with IEC 59 CO 11,
IEC 704, DIN 45635 Part 21, NFS 31-031
(84/538/EEC).
The value of the vibrations emitted on the hand is
4,65 m/s 2 . This value was determined in compliance
with ISO 5349.
5. Fitting the guard, handle, skids and
retractable underarm support
(Fig. 3 - 7)
Fasten the edge guide (9) to the projections on
the guard (12) (see arrows/Fig. 3).
Then mount the guard on the engine head (see
Fig. 4) and fasten with the supplied screws (see
Fig. 5)! If required, the skids (Fig. 6/Item 11) can
be mounted on the guard. Please make sure that
they lock into place properly.
The handle (5) is fitted as shown in Fig. 7. To do
this, pull both ends of the handle gently apart.
Then fasten with the fastening screw (6).
The retractable underarm support is fitted as
shown in Fig. 6a.

6. Proper use

The trimmer is designed for cutting lawns and small
areas of grass in private and hobby gardens.
Tools for private and hobby gardens are not suitable
for use in public facilities, parks and sport centers,
along roadways, on farms or in the forestry sector.
For the tool to be used properly it is imperative to
follow the instructions set out in the manufacturer's
directions for use.
14.01.2005 11:01 Uhr Seite 17
Important! It is prohibited to use the tool to chop
material for composting because of the potential
danger to persons and property.
230V ~ 50 Hz
500 W

7. Before using for the first time

ø 27 cm
10.500 rpm
Adjust the height and the auxiliary handle to achieve
ø 1.4 mm
an optimum working position.
84 dB(A)
96 dB(A)
7.1 Height adjustment (see Fig. 8)
4,65 m/s 2
Set the grass trimmer down firmly on the ground.
Slacken the telescope gland (7) in the direction of the
3,5 kg
arrow. Then adjust the telescopic tube to the length
required and tighten the telescope gland again when
you have done so.
7.2 Adjusting the auxiliary handle (see Fig. 9)
Set the grass trimmer down firmly on the ground.
Slacken the screw (6) and adjust the auxiliary handle
to the optimum position. Fasten the handle in
position by tightening the screw.
7.3 Adjusting the angle of inclination of the long
handle (see Fig. 10)
Set the grass trimmer down firmly on the ground.
Press your foot on the pedal on the side of the
engine housing. You can now adjust the long handle
to the desired angle of inclination. To fasten the long
handle at this angle of inclination, release the pedal
and let the handle lock in position.
7.4 Retractable underarm support (see Fig. 11)
The grass trimmer comes with a retractable
underarm support. The support must be pulled out so
far that it audibly locks into place (see Fig. 12).

8. Starting for the first time

The grass trimmer is designed for the trimming of
grass only.
The grass trimmer comes with a fully automatic line
extension system. Whenever the line on the grass
trimmer is reduced in length during operation to
approx. ø 230 mm, it will be extended automatically
to the maximum cutting width (approx. 270 mm). This
means that you can work with the optimum cutting
width at all times.
Important:
When you use your machine for the first time it is
possible that the projecting excess end of the
cutting line may be cut by the cutter blade on the
guard.
GB
17