Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
TOOLS AND PARTS
IMPORTANT:
Installer: Leave Installation Instructions with the
homeowner.
Homeowner: Keep Installation Instructions for future
reference. Save these Installation Instructions for the
local electrical inspector's use.
TOOLS NEEDED:
Gather the required tools and parts before starting
installation. Read and follow the instructions provided
with any tools listed here.
Cordless drill
Drill bits
Adjustable
wrenches (2)
Phillips screwdriver
Small level
Appliance dolly
Torx
T27 screwdriver Utility knife
†
Parts Needed:
#8 x 3" (7.6 cm) wood screws (longer screws may
be needed) (6)
2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)
(1 or 2)
If you are connecting the water line directly to copper
tubing and not to a shutoff valve, you need a ferrule, a
union, and a 1/4" (6.35 mm) compression fitting.
LOCATION REQUIREMENTS
The refrigerator can be recessed in an opening between
cabinets or installed at the end of a cabinet run using a
side panel to enclose the refrigerator.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
IMPORTANT: This appliance is intended to be used in
household and similar applications such as:
Staff kitchen areas in shops, offices and other working
environments.
Farm houses and by clients in hotels, motels and
other residential type environments.
Bed and breakfast type environments.
Catering and similar non-retail applications.
†TORX is a trademark of Acument Intellectual Properties, LLC.
INSTALLATION REQUIREMENTS
11/32" nut driver
3/8" and 1/2" open-end
wrenches
5/32" hex key
1/4" and 5/16" socket
drivers
Tape measure
NOTE: The refrigerator is intended for use in a location
where the temperature ranges from a minimum of 55°F
(13°C) to a maximum of 110°F (43°C). The preferred room
temperature range for optimum performance, which
reduces electricity usage and provides superior cooling, is
between 60°F (15°C) and 90°F (32°C). It is recommended
that you do not install the refrigerator near a heat source,
such as an oven or radiator.
IMPORTANT:
Observe all governing codes and ordinances.
Floor must support the refrigerator weight, more
than 600 lbs (272 kg), door panels and contents of
the refrigerator. Flooring under refrigerator must be
at same level as the room. Face of cabinetry must be
plumb.
Location should permit door to open fully. See "Door
Swing Dimensions."
Location must permit top grille removal. See
"Opening Dimensions."
OPENING DIMENSIONS
To avoid tipping during use, the solid soffit must be
within 1" (2.5 cm) maximum above the refrigerator. If
the solid soffit is higher than 1" (2.5 cm) or one is not
available, then the refrigerator must be braced.
If anti-tip boards are needed, they must be installed
to the rear wall studs so that the bottom of the anti-
tip board is 84" (213 cm) from the floor. See "Install
Anti-Tip Boards" for more information.
NOTES:
A clearance of 1/2" (1.3 cm) must be maintained
above the top grille in order for the top grille to be
removed.
Do not remove the foam gasket from the top of
the compressor cover unless removal is necessary
to fit the unit under a soffit. Removal of the
gasket will cause loss in cooling efficiency.
If installing under a solid soffit, after, installation
raise the leveling legs so that the gasket is
pressed snugly against the soffit.
A
B
A. Gasket
B. Compressor cover
A grounded 3 prong electrical outlet should be
located within a specified number of inches from
the right-hand side cabinets or end panel. See the
chart following the graphic for the number of inches
required for your model. For more information, see
"Electrical Requirements."
1/2"
(1.3 cm)
5
Publicité
Table des Matières
