Changing The Master Code - CDVI Digicode SUBLIM Manuel D'installation

INSTALLATION MANUAL
SUBLIM
Illuminated Weatherproof Keypad with remote electronics
4. Press B to exit from programming mode.
2 beeps are emitted to confi rm that the
keypad is in stand-by operating mode.
4 beeps indicate a data computing error.
EXAMPLE:
You have a master code and user codes
using 5 digits. You want to use 4 digit codes.
Carry out the procedure described above
to change the master code. When the
number of master code digits has been
changed from 5 to 4 digits, user codes
become 4 digit codes at the same time.
E.g.: If your master code or user code
is 1 2 3 6 9, afterwards it will become 2 3 6 9.
If you want to change a master code
(and therefore a user code) from 4 digits
to 5 digits, follow the same procedure.
When you change from 4 to 5 digits, the fi gure
"0" will be added at the beginning of the master
code by default and therefore at the beginning
of the user codes.
E.g.: Changing the 4 digit master code
2 3 6 9 into 5 digits becomes 0 2 3 6 9.
We recommend programming
codes in 5 digits and then changing
the number of digits.
C. CHANGING THE MASTER CODE
The master code is used only to enter
in programming mode.
1. Enter the master code twice.
(1 2 3 4 5 default value master code).
2 beeps are emitted to confi rm
entry in programming mode.
2. Press A5 to modify the master code.
- One beep is emitted.
- Enter the new 4 or 5 digits master code.
- One beep is emitted to confi rm
that the master code is programmed.
3. Press B to exit from the programming mode.
2 beeps are emitted to confi rm that
the keypad is in stand-by operating mode.
cdvi.com
6
cdvigroup.com
D. ADDING, CHANGING
OR DELETING A USER CODE
Code groups (also called rows for ranking
codes per individual) are different :
- Relay 1 (Group 1: From address 00
to address 59, relay output 1.
- Relay 2 (Group 2: From address 60
to address 99, relay output 2).
1. Enter the master code twice
(1 2 3 4 5 default value master code).
2 beeps are emitted to confi rm entry
in programming mode.
2. To add a user code, enter the user
location (from 00 to 99).
If the user location is used 4 beeps are emitted,
enter the 4 or 5-digits User code.
3. To Change a User code enter
the user location.
- 4 beeps are emitted to indicate that
the user location is already programmed.
- Enter a new 4 or 5-digits code.
- A beep is emitted to confi rm the new user code.
3. Press B to exit programming.
Two beeps are emitted to confi rm
the return to normal operating mode.
4. To delete a User code enter
the user location.
- 4 beeps are emitted.
- Press 0 0 0 0 0 in 5-digits length code
or 0 0 0 0 in 4-digits length code.
- A beep is emitted to confi rm the user
code has been deleted.
If the code entered corresponds
existing code or if it is the same as the
master code, 4 beeps indicate an error.
The codes 0 0 0 0 0 and 0 0 0 0 are used
to cancel an existing code and therefore
cannot be used as door opening codes.
E. TIME OUTPUTS
This section allows to program the illumination
time and the Relay activation time.
1. Enter the master code twice
EN
to an