Programming Functions; Changing The Master Code - CDVI GALEO Manuel D'installation

Masquer les pouces Voir aussi pour GALEO:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

INSTALLATION MANUAL
GALEO
Weatherproof Illuminated Keypad with remote electronics

7] PROGRAMMING FUNCTIONS

DEFAULT VALUES
- Without codes.
- Illumination time: 10 seconds.
- Relay release time: 1 second.
- Code length: 5-digit.
- Master Code: 1 2 3 4 5.
- Programming security time :
120 secondes.
- Code length for sub master code:
Version 1 relay (Group 1) =
A and B,
Version 2 relays (Group 2) =
1 and 3
Version 3 relays (Group 3) =
4 and 6.
A. RESET MASTER CODE
AND USER CODES
1. Enter the master code twice
(1 2 3 4 5 default value master code).
2 beeps are emitted to confirm entry
in programming mode.
2. Press A6 to reset the Master Code
and the User codes.
One beep is emitted. Press on A and B to confirm
reset of all memory of the keypad. Wait for two
beeps. The master code is restored to its default
value 1 2 3 4 5 and all the User codes are deleted
from the keypad. Once the reset is completed then
the keypad returns to a stand-by
operating mode.
OR
1. Cut the power. Put the jumper on P2.
2. Put the power back.
Wait approximately 3 seconds.
Two beeps are emitted to confirm reset
of the keypad. Remove P2 jumper. The master
code is restored to its default value 1 2 3 4 5
and all the User codes are deleted from
the keypad.
B. SETTING CODE LENGTH
6
cdvigroup.com
AUDIBLE SIGNAL:
The buzzer indicates different
audible signals. It can be turned
off by cutting the ST1 wire on the
remote controller
1 short beep: Keypad powered
1 long beep: data computing in
programming or access granted
2 short beeps: Enter or Exit from
programming
4 short beeps: data computing
error.
CODE LENGTH
The master code and the User codes
can be of 4 or 5-digit in length.
All the keypad keys can be used to
1. Enter the master code twice.
(1 2 3 4 5 default value master code).
2 beeps are emitted to confirm entry
in programming mode.
2. Press A4 to program the code length.
One beep is emitted. Press 4 or 5 for the digit
code. One beep is emitted to confirm programming
of the code length.
3. Press A5 to modify the master code.
One beep is emitted. Enter the new 4 or 5-digit
master code. One beep is emitted to confirm pro-
gramming of the new master code.
4. Press B to exit from programming mode.
2 beeps are emitted to confirm that the keypad
is in stand-by operating mode.
4 beeps indicate a data computing error.
C. CHANGING THE MASTER CODE
The master code is used only to enter
in programming mode.
1. Enter the master code twice.
(1 2 3 4 5 default value master code). 2 beeps
are emitted to confirm entry in programming mode.
program a code. The master code and
the Pin code can be of 4 or 5-digit code.
The master code CAN NOT be used as
a PIN code (User Pin code). The master
code CAN NOT be used as a PIN code
(User Pin code). To delete a specific
User pin Code replace it by 0000 if code
length is 4-digit format or replace it by
00000 if the code is in 5-digit format.
P2 JUMPER:
Reset master code
and user codes.
P3 JUMPER:
modification of individual
code by the user.
EN

Publicité

Table des Matières
loading

Table des Matières