Publicité
Les langues disponibles
Les langues disponibles
User Manual of Water-Proof Brushless Speed Controller (RTR Version)
2. Programmable Items list
Programmable Items
1
2
Forward with
Forward/Reverse
1. Running Mode
Brake
with Brake
2. Drag Brake Force
0%
5%
3. Low Voltage Cut-Off
2.6V
Non-Protection
Threshold
/Cell
4. Start Mode
Level1
Level2
(Punch)
(Soft)
5. Maximum Brake Force
25%
50%
Attention: The italics texts in the above form are the default settings.
3. Programmable Items
3.1. Running Mode: With "Forward with Brake" mode, the car can go forward and brake, but cannot go backward, this mode
is suitable for competition; "Forward/Reverse with Brake" mode provides backward function, which is suitable for training.
Note: "Forward/Reverse with Brake" mode uses "Double-Click" method to make the car go backward.
When you move the throttle stick from forward zone to backward zone for the first time, the ESC begins to brake the motor,
the motor speeds down but it is still running, not completely stopped, so the backward action is NOT happened now. When the
throttle stick is moved to the backward zone again (The 2
the backward action will be occurred. The "Double-Click" method can prevent mistakenly reverse when the brake function is
frequently used in steering.
3.2. Drag Brake Force: Set the amount of drag brake applied at neutral throttle to simulate the slight braking effect of a neutral
brushed motor while coasting.
3.3. Low Voltage Cut-Off: The function is mainly used to prevent the Lipo battery from over discharging. The ESC monitors the
battery's voltage at any time, if the voltage is lower than the threshold, the output power will be reduced to 50% in 2 seconds.
Please drive to the side of racing track as soon as possible and then stop the car, the ESC will completely cut off the output
power in 10 seconds. The values listed in the table refer to the cut-off threshold for each Lipo cell.
3.4. Start Mode (Also called "Punch"): Select from "Level1 (Soft)" to "Level 4 (Very aggressive)" start mode as you like.
Please note that if you choose "Level 4(Very aggressive)", you should use good quality battery with powerful discharge ability,
otherwise you cannot get the bursting start effect as you want. If the motor cannot run smoothly (that is: the motor is trembling),
it may caused by the weak discharge ability of the battery, please choose a better battery or increase the gear rate.
3.5. Maximum Brake Force: The ESC provides proportional brake function. The brake force is related to the position of the
throttle stick. Maximum brake force refers to the force when the throttle stick is located at the top point of the backward zone.
A very large brake force can shorten the brake time, but it may damage the gears.
4. Reset All Items To Default Values
At any time when the throttle is located in neutral zone (except in the throttle calibration or programming mode), hold the "SET"
key for over 3 seconds, the red LED and green LED will flash at the same time , which means each programmable item has
be reset to its default value. It needs to be restarted to complete the whole process.
[OPTIONAL ACCESSORIES]
We provide the following optional accessories:
1. Cooling fan (12V): The high voltage fan is an option when you use 3S Lipo or NiMH
battery more than 6 cells.
WARNING! Please note the original cooling fan (5V) is only allowed to work with 2S
Lipo or 4-6 cells NiMH battery. Please DON'T use it with a 3S Lipo or NiMH battery
more than 6 cells.
2. LED Program Card (Digital LED Display)
The LED Program Card is an optional accessory which needs to be purchased
separately. It has a friendly user interface. The process of programming the ESC
becomes quite easy and fast with this pocket sized device.
Programmable Value
3
4
5
6
10%
15%
20%
25%
2.8V
3.0V
3.2V
3.4V
/Cell
/Cell
/Cell
/Cell
Level4
Level3
(Very Aggresive)
75%
100%
"click"), if the motor speed is slowed down to zero (i.e. stopped),
nd
Mark: Direction of the airflow and the
impeller
Fan
Heat Sink
Speed Controller
Please connect the ESC to LED Program Card via the program port.
●
For WP-S16-RTR ESC, the program port is multiplexed with the Rx wire, please disconnect the Rx wires from receiver
and then connect it to LED program card.
7
8
●
For WP-S10C, WP-S10D, WP-S10DS, WP-S10E, WP-10BL60 ESC, the program port is multiplexed with the cooling
fan port, please disconnect the cooling fan, and then use program cable to connect the fan port of the ESC to the LED
program card.
30%
40%
[TROUBLE SHOOTING]
Trouble
After power on, motor can't work, no sound
is emitted.
After power on, motor can't work, but emits
"beep-beep-, beep-beep-" alert tone. (Every
"beep-beep-" has a time interval of 1 second.)
After power on, motor can't work, but emits
"beep-, beep-, beep-" alert tone. (Every "beep-"
has a time interval of about 2 seconds.) And
the red LED solid lights.
After power on, motor can't work and the red
LED blinks very quickly.
The motor runs in the opposite direction.
The motor suddenly stops running while in
working state.
Random stop or restart or irregular working
state.
W: White wire
Cooling fan port
R: Red wire
B: Black wire
The cooling fan port is also a
program port for the ESC
Connect to LED Program Box
Possible Reason
The connections between battery pack
Check the power connections.
and ESC are not correct.
Replace the connectors.
Input voltage is abnormal, too high or too
Check the voltage of the battery pack.
low.
Check the transmitter and the receiver.
Throttle signal is abnormal.
Check the wire of the throttle channel.
Calibrate the throttle range for the ESC again,
The neutral point of the throttle channel
or adjust the trimmer of throttle channel (on the
is changed.
transmitter) to change the neutral point.
The wire connections between ESC and
Swap any two wire connections between the ESC
the motor need to be changed.
and the motor.
Check the transmitter and the receiver
The throttle signal is lost
Check the wire of the throttle channel
The ESC has entered the Low Voltage
Replace the battery pack.
Protection Mode.
Check all the connections: battery pack
Some connections are not reliable.
connections, throttle signal wire, and motor
connections, etc.
Reset the ESC. If the function could not be
There is strong electromagnetic
resumed, you might need to move to another
interference in flying field.
area to run the car.
Page - 3 -
Solution
Publicité
