Publicité
Les langues disponibles
Les langues disponibles
User Manual of Water-Proof Brushless Speed Controller (RTR Version)
2. Throttle Range Setting (Throttle Range Calibration)
In order to make the ESC match the throttle range, you must calibrate it when you begin to use a new ESC, or a new transmitter,
or after changing the settings of the neutral position of throttle channel, ATV or EPA parameters, otherwise the ESC cannot
work properly.
There are 3 points need to be set, they are the top point of "forward", "backward" and the neutral point. The following pictures
show how to set the throttle range with a Futaba
TM
A) Switch off the ESC, turn on the transmitter, set
the direction of throttle channel to "REV", set the
"EPA/ATV" value of throttle channel to "100%",
and disable the "ABS" brake function of your
transmitter.
(*Note2)
B) Hold the "SET" key and then switch on the ESC,
when the red LED begins to flash, release the
key immediately.
(Please check the picture on the right side)
C) Set the THREE points according to the steps
shown in the picture on the right side.
1) Neutral point
2) End point of forward direction
3) End point of backward direction
D) When the process of calibration is finished, the
motor can be started after 3 seconds.
Note2: If you don't release the "SET" key after the
red LED begins to flash, the ESC will enter the
program mode, in such a case, please switch off
the ESC and re-calibrate the throttle range again
from step A to step D.
3. The LED Status in Normal Running
a) When the throttle stick is in the neutral range, neither the Red LED nor the Green LED lights up.
b) When the car moves forward, the Red LED solidly lights; the Green LED also lights up when the throttle stick is at the
top position (100% throttle).
c) When the car brakes, the Red LED solidly lights; the Green LED also lights up when the throttle stick is at the bottom
position and the maximum brake force is set to 100%.
d) When the car reverses, the Red LED solidly lights.
[ALERT TONES]
1. Input voltage abnormal alert tone: The ESC begins to check the input voltage when power on, if it is out of the normal
range, such an alert tone will be emitted: "beep-beep-, beep-beep-, beep-beep-" (There is 1 second time interval between
every "beep-beep-" tone).
2. Throttle signal abnormal alert tone: When the ESC can't detect the normal throttle signal, such an alert tone will be emitted:
"beep-, beep-, beep-" (There is 2 seconds time interval between every "beep-" tone).
[PROTECTION FUNCTION]
1. Low voltage cut-off protection: If the voltage of a Lipo battery pack is lower than the threshold for 2 seconds, the ESC will
cut off the output power. Please note that the ESC cannot be restarted if the voltage of each Lipo cell is lower than 3.5V.
For NiMH battery packs, if the voltage of the whole NiMH battery pack is higher than 9.0V but lower than 12V, it will be
considered as a 3S Lipo; If it is lower than 9.0V, it will be considered as a 2S Lipo. For example, if the NiMH battery pack
is 8.0V, and the threshold is set to 2.6V/Cell, it is considered as a 2S Lipo, and the low-voltage cut-off threshold for this
NiMH battery pack is 2.6*2=5.2V.
2. Over-heat protection: When the temperature of the ESC is over a factory preset threshold for 5 seconds, the ESC will cut
off the output power. You can disable the over-heat protection function for competition race.
3. Throttle signal loss protection: The ESC will cut off the output power if the throttle signal is lost for 0.2 second.
transmitter.
Push
SET
Hold the SET button
Turn on the switch
Release the SET button as soon
as the red LED starts to blink
Neutral point
Top point of full throttle
1st Click
2nd Click
LED
LED
Green LED flashes once
Green LED flashes twice
Green LED flashes thrice
[PROGRAM THE ESC]
1. Program Method
Turn off the ESC,
Turn on the transmitter
Hold the SET key,
Switch on the ESC
Red LED flashes
LED
Green LED flashes
for 1 time
Hold SET key for 3 seconds
Top point of full brake
Green LED flashes
for 2 times
3rd Click
Hold SET key for 3 seconds
Green LED flashes
for 3 times
Hold SET key for 3 seconds
LED
······The following steps are just like the above steps······
Hold SET key for 3 seconds
Green LED flashes
for N times
Note:
●
In the program process, the motor will emit "Beep" tone when the LED is flashing.
●
The 5
programmable item is represented by 5 short Beeps (that is, "BBBBB").
th
●
For the options of each programmable item, we use a long time flash and long "Beep---" tone to represent number "5", so
it is easy to identify the options with big numbers.
For example, if the LED flashes as the following:
"A long time flash" (Motor sounds "B---") = The option 5
"A long time flash + a short time flash" (Motor sounds "B---B") = The option 6
"A long time flash + 2 short times flash" (Motor sounds "B---BB") = The option 7
"A long time flash + 3 short times flash" (Motor sounds "B---BBB") = The option 8
Enter the corresponding
Press the SET key to choose the
programmable item, the
programmable value, the RED LED
RED LED flashes for several
flashes for several times, the times
times, the times presents the
presents the serial number of the
current value of this item
value you are choosing
Red LED flashes for 1 time to choose
Enter the 1st item
"Forward with brake"
"Running Mode"
Release
Press
Red LED flashes for 2 times to choose
SET key
SET key
"Forward/Reverse with brake"
Red LED flashes 1 time, choose "0%"
Enter the 2nd item
Red LED flashes 2 times, choose "5%"
"Drag Brake Force"
Release
Red LED flashes 3 times, choose "10%"
Press
SET key
SET key
Red LED flashes 4 times, choose "15%"
Red LED flashes 5 times, choose "20%"
Red LED flashes 6 times, choose "25%"
Red LED flashes 7 times, choose "30%"
Red LED flashes 8 times, choose "40%"
Red LED flashes 1 time, choose "None"
Enter the 3rd item
Red LED flashes 2 times, choose "2.6V"
"Low Voltage Cut-off"
Release
Press
Red LED flashes 3 times, choose "2.8V"
SET key
SET key
Red LED flashes 4 times, choose "3.0V"
Red LED flashes 5 times, choose "3.2V"
Red LED flashes 6 times, choose "3.4V"
Press SET key to choose the value, the
flash times of RED LED means the serial
Enter the N
th
item
number of the value (1 time means the
Release
Press
1st value, 2 times means the 2nd value...)
SET key
SET key
Page - 2 -
Publicité
