Erreka AXIL Guide Rapide D'installation Et Programmation page 15

Electrical connections AX43 (230V / 50Hz) and AX43M (125V / 60Hz)

For the AX43 operator we recommend using the VIVO-M101 or VIVO-M201 control panel.

For the AX43M operator we recommend using the VIVO-M101M or VIVO-M201M control panel.
FCA2 COM FCC2
P1 P2 P3 P4 P5 P6 P15 P14 P16
ST1 FT1 ST2 FT2 FCA1 FCC1
T
G1/G4
G3/G6
G2/G5
AX43(M)

We recommend the VIVO-D201(M) control panel.
GND
V+
A1 Operator 1
A2 Operator 2
G1/G4 Red wire (motor)
G2/G5 Blue wire (motor)
V+ Brown wire
(encoder power supply)
GND Mesh (encoder mass)
SNG1 Green wire (encoder signal 1)
SW1 Main switch
• For the AXS4324 operator, programme C305.
• Check that parameter C7 is programmed for operation with encoder (C701).
• Select the number of operators using C0 (C001: one operator, C002: two operators).

Turning direction check: after connecting the power and activating any of the key devices, the gate makes a reset
(the display showsrS): the gate closes until it reaches the stopper, assigning this stopper with the position "gate
closed" If it opens instead of closes during reset, change the turning direction (C101 or C102 for the A1 operator,
and C201 or C202 for the A2 operator).
SCA
G4 G5
P7 P8 P11 P12 P22 P23 G7 G8 G9 G10
Courtesy
24Vac Lamp.
STOP LOCK
MOTOR2 (G2-G1-COM)
Light
G4
G5
G6
Electrical connections AXS4324 (24Vdc)
SNG1
ENCODER1 ENCODER2
P13 P14 P15 P16 P17 P18 P19 P20 P21 P22 P23
P1 P2 P3 P4 P5 P6 P7 P8
A1, A2
C1, C2
DL4
DL5:
PUL1
PUL2
T
Operator connections A1 / A2:
G1 / G4 open
G2 / G5 close
G3 / G6 common (COM), grey wire
G6 G1 G2 G3
N L
POWER
MOTOR1 (G2-G1-COM)
VIVO-M201:
230Vac/50Hz (AX43)
VIVO-M201M:
125Vac/60Hz (AX43M)
G1 G2 G3
P24 P25
MOTOR2
-FT
AUX
G4 G5
(Test) 24 Vdc
MOTOR1
P9 P10 P11 P12
G1 G2
operators
capacitors (supplied
inside the operator)
gate opening
gate closing
close mini-pushbutton
open mini-pushbutton
earth connection

When pressing PUL1, DL5 lights
up and the G2/G5 and G3/G6
cable connectors are activated.

When pressing PUL2, DL4 lights
up and the G1/G4 and G3/G6
cable connectors are activated.
If the turning direction is not
correct, interchange the G1
and G2 wires (for A1) or G4
and G5 (for A2).
P198W
SW1
G6
G7 G8 G9 G10
G3
V+
GND
T
G1/G4
G2/G5
SNG1
AXS4324
installed
N L
POWER - 230V
VIVO-D201:
VIVO-D201M:
P198Y
15