Table des Matières
Publicité
CARBURATORE
Tipo (TE 250) ..."Mikuni" TMR 36 con pompa di
ripresa e sensore T.P.S. (Throttle Position
Sensor)
Tipo (TC 250-SM400 R) .."Mikuni" TMR 38 con
pompa di ripresa e sensore T.P.S. (Throttle
Position Sensor)
Tipo (450)........."Mikuni" TMR 41 con pompa di
ripresa e sensore T.P.S. (Throttle Position
Sensor)
Diametro diffusore (TE 250)...................mm 36
Diametro diffusore (TC 250-SM 400 R) .mm 38
Diametro diffusore (450) ........................mm 41
Getto massimo (TE 250) .............................150
Getto massimo (TC 250).............................155
Getto massimo (SM 400 R).........................165
Getto massimo (450)...................................175
Getto minimo (250) ....................................22,5
Getto minimo (SM 400 R) ............................ 25
Getto minimo (TE, SMR 450)....................... 30
Getto minimo (TC 450).............................. 32,5
Valvola gas ...................................................1.0
Spillo conico ..................................................52
Tacca fiss. spillo
(TE 250, TE-TC-SMR 450) ...........................3a
Tacca fiss. spillo (TC 250-SM 400 R)............4a
Polverizzatore ...............................................P4
Vite aria aperta (250-400) .........................giri 2
Vite aria aperta (450) ..........................giri1+3/4
Getto pompa di ripresa (TE 250, TE 450, TC
450, SMR 450, SMR 400) .............................30
Getto pompa di ripresa (TC 250) ..................35
TRASMISSIONE PRIMARIA
Pignone motore (250).................................z 24
Pignone motore (400-450) .........................z 27
Corona frizione (250)..................................z 88
Corona frizione (400-450) ..........................z 85
Rapporto di trasmissione (250)................3,667
Rapporto di trasmissione (400-450).........3,148
30
CARBURETOR
Type (TE 250) ................."Mikuni" TMR 36 with
acceleration pump and T.P.S. (Throttle Position
Sensor)
Type (TC 250-SM 400 R)"Mikuni" TMR 38 with
acceleration pump and T.P.S. (Throttle Position
Sensor)
Type (450)..."Mikuni" TMR 41 with acceleration
pump and T.P.S. (Throttle Position Sensor)
Venturi diameter (TE 250 ......................1.42 in.
Venturi diameter (TC 250-SM 400 R)....1.50 in.
Venturi diameter (450)...........................1.61 in.
High speed jet (TE 250)..............................150
High speed jet (TC 250) .............................155
High speed jet (SM 400 R) .........................165
High speed jet (450) ...................................175
Low speed jet (250) .................................. 22,5
Low speed jet (SM 400R) .............................25
Low speed jet (TE, SMR 450).......................30
Low speed jet (TC 450) .............................32,5
Throttle piston ..............................................1.0
Metering pin ..................................................52
Metering pin groove
(TE 250, TE-TC-SM 450 R).........................3rd
Metering pin groove
(TC 250 - SM 400 R)......................................4th
Main nozzle ....................................................P4
Idle mixture adjusting screw (250-400) (turns)..2
Idle mixture adjusting screw (450) (turns) . 1+3/4
Acceleration pump jet (TE 250, TE 450, TC
450, SMR 450-SMR 400)..............................30
Acceleration pump jet (TC 250)....................35
PRIMARY DRIVE
Drive pinion gear (250) ..............................z 24
Drive pinion gear (400-450) .......................z 27
Clutch ring gear (250) ................................z 88
Clutch ring gear (400-450).........................z 85
Transmission ratio (250) ..........................3,667
Transmission ratio (400-450) ...................3,148
CARBURATEUR
Type (TE 250)"Mikuni" TMR 36 avec pompe de
reprise et T.P.S. (Capteur position du papillon
carburateur)
Type (TC 250-SM 400R) "Mikuni" TMR 38 avec
pompe de reprise et T.P.S. (Capteur position
du papillon carburateur)
Type (450) Mikuni" TMR 41 avec pompe de
reprise et T.P.S. (Capteur position du papillon
carburateur)
Diamètre diffuseur (TE 250)...................mm 36
Diamètre diffuseur (TC 250 SM400 R)...mm 38
Diamètre diffuseur (450) ........................mm 41
Gicleur principal (TE 250) ...........................150
Gicleur principal (TC 250) ...........................155
Gicleur principal (SM 400 R) .......................165
Gicleur principal (450) .................................175
Gicleur ralenti (250)....................................22,5
Gicleur ralenti (SM400 R)..............................25
Gicleur ralenti (TE, SMR 450) ..................... 30
Gicleur ralenti (TC 450)............................ 32,5
Soupape gaz ................................................1.0
Épingle conique.............................................52
Coche fixation épingle conique
(TE 250, TE-TC-SM 450 R) .....................3ème
Coche fixation épingle conique
(TC 250 - SM 400 R)................................4ème
Pulverisateur.................................................P4
Vis air ouverte de tours (250)....................giri 2
Vis air ouverte de tours (450).................. 1+3/4
Gicleur pompe de reprise (TE 250, TE 450,
TC 450, SMR 450 - SMR 400) ......................30
Gicleur pompe de reprise (TC 250)...............35
TRANSMISSION PRINCIPALE
Pignon moteur (250)...................................z 24
Pignon moteur (400-450) ...........................z 27
Couronne embrayage (250) .......................z 88
Couronne embrayage (400-450) ................z 85
Rapport de transmission (250).................3,667
Rapport de transmission (400-450) .........3,148
Publicité
Table des Matières
