Technical Data - VOLTCRAFT Mega 24000 SL-240 Mode D'emploi

Briefly press the function switch (1) to display the internal battery charge level. The remaining
capacity of the battery is indicated by the lit LEDs as follows:
1 LED: Remaining capacity up to 25%
2 LEDs: Remaining capacity up to 50 %
3 LEDs: Remaining capacity up to 75 %
4 LEDs: Remaining capacity up to 100 %
a) USB
• Use the included USB charging cable to connect the Micro USB plug to the Micro USB
input (9).
• Connect the USB-A plug to a suitable USB power source (for example, a USB power adapter
with 2000 mA output current). The charging time is approx. 14 – 15 hours.
• You can also use the included USB-C
USB-CTM input . The charging time is approx. 11 – 12 hours.
(10)
• The product can also be charged simultaneously via the Micro USB input and USB-C
This can increase the charging current and the battery can thus be charged faster.
• The battery level indicator (2) flashes during charging.
0 – 25% 25 – 50 %
LED 1 Flashes blue Solid blue
LED 2 off Flashes blue
LED 3 off
LED 4
off
LED 1 is located directly next to the function switch. LED 4 is located on the outside.
• When the rechargeable battery is fully charged, the battery level indicator will turn off.
• Disconnect the cable from the product and the power source as soon as the rechargeable
battery is fully charged. The product is ready for use.
If you only use the product occasionally, we recommend that you fully charge the
internal battery every 6 months in order to retain maximum capacity.
b) Solar panel
The solar panel is only used for emergency power supply if there is no mains supply
available.
Subjecting the solar panel to direct sunlight for a prolonged period may damage the
solar panel.
• Place the product with the solar panel (3) up in direct sunlight.
The solar panel can also generate power from artificial light.
• The solar charging lamp (4) is solid green while the internal battery is being charged via the
solar panel.
Charging mobile devices
• Connect your mobile device with one of the USB outputs.
• Fast charging is possible via the orange marked USB-A output 2 (8). In addition, this output
can be used to charge the devices with different voltages (5 V, 9 V and 12 V).
You can charge up to 3 devices at a time. The maximum charging current is 6 A.
• The battery level indicator glows steadily and indicates the current charge level of the power
bank.
The charging currents of the USB outputs can be found in "Technical data". Check
the charging current of your mobile device.
The internal battery must be sufficiently charged so that 2 or 3 devices can be
charged at a time.
• If the charging process does not start automatically, press the function switch to turn on the
product.
• Monitor the charging process. Remove the USB cable from the product and the mobile
device as soon as the charging process is complete.
If the internal battery charge level becomes too low, the product will turn off
automatically to prevent excessive discharge of the internal battery.
LED torch
• To turn on the torch, press and hold down the function switch for approx. 3 seconds.
• Then briefly press the function switch to change the lighting mode and toggle to flashing light
and SOS signal. The torch toggles in the following order:
Solid light → flashing light → SOS signal → light off
• To turn on the torch again, press and hold down the function switch for approx. 3 seconds.
Press and hold down the function switch for approx. 3 seconds to turn off the torch directly
again.
charging cable to charge the internal battery via the
TM
50 – 75 % 75 – 99 %
Solid blue Solid blue
Solid blue Solid blue
off Flashes blue Solid blue
off off Flashes blue
Carabiner
• Connect the carabiner hook to the eyelet (5) to attach the product, for example, to a backpack.
• You can also hang the product on a suitable hook without the carabiner. Make sure that the
product does not fall.
Troubleshooting
Problem
Battery level indicator
LEDs are not bright
enough
LEDs light up even
though the charging
input.
TM
cable is disconnected.
Care and cleaning
100 %
• Disconnect the product from the connected devices before cleaning.
Solid blue
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
Solid blue
• This product does not contain any components that require maintenance. Never attempt to
Solid blue
open or disassemble it.
• Use a lint-free cloth to clean the product. Do not press too hard on the housing, as this can
Solid blue
lead to scratch marks.
• Dust can be easily removed using a soft and clean long-haired brush.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product according to
the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the
environment.

Technical data

Input voltage/current ..................... Micro USB: 5 V/DC 2 A, 9 V/DC 2 A
Output voltage/current .................. USB-A (orange): 5 V/DC 3 A, 9 V/DC 2 A, 12 V/DC 1.5 A
Solar charging current .................. 5 V/DC 400 mA max.
Battery .......................................... LiPo, 24000 mAh
LED torch ..................................... Colour temperature 6000 – 6500 K
Protection type .............................. IP67
Operating/storage temperature .... 0 to +45 °C
Dimensions (L x W x H) ................ 180 x 89 x 30 mm
Weight .......................................... 553 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE.
Cause Solution
Incompatible charging cable Use the included charging
used cable.
Poor contact at Micro USB Disconnect the USB plug and
input or USB output connect it again.
LEDs glow for a while after LEDs will go off automatically
the charging cable has been after approx. 15 seconds.
disconnected.
USB-C : 5 V/DC 3 A max.
TM
USB-A: 5 V/DC 2.4 A
USB-C : 5 V/DC 3 A max.
TM
*1662034_v2_0818_02_hk_m_en