Important; Cleaning And Maintenance; Technical Data - VOLTCRAFT PB-15 Mode D'emploi

D o not use any USB ports such as those of a keyboard or a USB hub which are not
equipped with an own power supply; the available current will not be sufficient.
• T hen connect the micro USB plug of the USB Y-cable to the micro USB socket of the power
bank.

Important!

A lways connect first both USB A plugs of the included USB Y-cable to your PC or
a USB hub with its own power supply and only then connect the micro USB plug to
the corresponding socket of the power bank.
• The LEDs indicate the status of the battery during charging.
S teady lit LEDs indicate the actual charging degree (1 LED steady = battery is charged
25% , 2 LEDs = 50%, 3 LEDs = 75%, 4 LEDs = 100%), while flashing lights indicate the
remaining part of the battery which still has to be recharged.
E xample: 3 LEDs are on, one LED is flashing: The battery has been charged up to at least
75%, and is charging the remaining 25%.
• T he charging time depends on the charge status of the battery and can last for several
hours (for charging time of a fully discharged battery, see chapter "Technical data").
• O nce the built-in rechargeable battery of the power bank is fully charged, disconnect the
micro USB connector from the power bank . The power bank is now ready for use.
d) Charging a mobile device
• D isconnect the power bank from the charging cable first, then unplug the micro USB con-
nector from the power bank.
I t is not possible to simultaneously use the charging output and recharge the power
bank.
• C onnect the large USB A socket on the power bank to your mobile device/ smartphone
using a suitable cable.
• I f the power bank does not turn on automatically, press the.control key briefly. The blue
LEDs show the present charge level of the built-in rechargeable battery (1 LED is on = 25%,
2 LEDs = 50%, 3 LEDs = 75%, 4 LEDs = 100%). A single flashing LED indicates that the
charge level is below 25%.
• M onitor the charging process. Once the mobile device/smartphone is fully charged (or the
rechargeable battery of the power bank is empty), the power bank will turn off.
• T o stop charging, disconnect the cable connection between your mobile device/smartphone
and the power bank by unplugging the USB connector of the cable from the USB A socket
on the power bank.
T he power bank turns off automatically after a few seconds, and the blue LEDs of the
charge status indication go dark.
e) Using the torch function
Press the control key 2x briefly to turn the white LED on or off.
A s a result of this, the blue LED of the charge status indication are activated at the
same time, see a) above.
CLEANING AND MAINTENANCE
The product does not require any maintenance and should never be disassembled for any
reason. The rechargeable battery is permanently installed and cannot be replaced.
Clean the product carefully, e.g. with a soft, clean cloth. Dust can be easily removed with a
soft, clean brush and a vacuum cleaner.
Never use aggressive cleaning agents and no chemicals at all for cleaning; these can lead
not only to discolouration, but can also damage the product.
DISPOSAL
E lectronic devices are recyclable material and do not belong in the household
waste.
P lease dispose of the device, when it is no longer of use, according to current statu-
tory requirements.
TECHNICAL DATA
Charging input ......................................1x micro USB port
Input voltage/current . ............................5 V/DC, max. 1 A
Charging output . ...................................1x USB port of type A
Output voltage/current . .........................5 V/DC, max. 1.5 A
Internal rechargeable battery . ...............LiPo, 3.7 V, 5200 mAh
Charging duration . ................................approx. 7 h at fully discharged rechargeable battery
Ambient conditions ............................... t emperature -20 °C to +60 °C, air humidity 30% to
Dimensions (W x H x D) .......................92 x 23 x 47 mm
Weight ..................................................115 g
80% relative, not condensing
Legal notice
G
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent
the technical status at the time of printing.
© Copyright 2015 by Conrad Electronic SE.