Technical Data; Battery Level Indicator - VOLTCRAFT SL-160 Mode D'emploi

Charging the battery
Fully charge the built-in rechargeable battery before first use.
Before charging the internal battery, ensure that the USB power source can deliver
a sufficient charging current, otherwise you may damage the product.
Do not use a USB port on a computer, keyboard or USB hub without power adapter
to charge the internal battery, as the current supplied by these ports is not sufficient.
When charging the product via USB, make sure that no sunlight falls on the solar
panel. Otherwise, the internal rechargeable battery may overheat.
Ensure that the connected devices' specifications conform to the product's
specifications listed in the technical data section.
Do not short-circuit the USB outputs.
a) USB
• Connect the Micro USB plug of the enclosed cable with the Micro USB input (4).
• Connect the USB plug with a suitable USB power source (e.g. USB power supply with
2000 mA output current).
• The battery level indicator (5) flashes during charging.
0 – 25% 25 – 50 %
LED 1 Flashes blue Solid blue
LED 2 off Flashes blue
LED 3 off
LED 4 off
LED 1 is located directly next to the on/off switch.
LED 4 is located directly next to the eyelet.
• When the rechargeable battery is fully charged, the battery level indicator will turn off.
• Disconnect the cable from the product and the power source as soon as the rechargeable
battery is fully charged. The product is now ready for use.
If you only use the product occasionally, we recommend that you fully charge the
internal battery every 6 months in order to retain maximum capacity.
b) Solar panel
The solar panel is only used for emergency power supply if there is no mains supply
available.
Subjecting the solar panel to direct sunlight for a prolonged period may damage the
solar panel.
• Place the product with the solar panel (8) facing up in direct sunlight.
The solar panel can also generate power from artificial light.
• The LED next to the on/off switch lights up green when the internal battery is charged via
the solar panel.
Charging mobile devices
• Connect your mobile device with one of the USB outputs.
The USB output (7) on the long side of the housing supplies a charging current of
max. 1000 mA.
The USB output (3) on the short side of the housing supplies a charging current of
max. 2400 mA.
The internal rechargeable battery must be fully charged to charge 2 devices
simultaneously.
• If the charging process does not start automatically, press the on/off switch (6).
• Monitor the charging process. Remove the USB cable from the product and the mobile
device as soon as the charging process is complete.
• To turn off the product, press and hold the on/off button for about 2 seconds.
If the charging status is less than 2 %, the product automatically turns off to prevent
excessive discharge of the internal battery.

Battery level indicator

Press the on/off switch (6) to show the battery level of the internal battery.
50 – 75 % 75 – 99 %
Solid blue Solid blue
Solid blue Solid blue
off Flashes blue Solid blue
off off Flashes blue
LED light
• Double-click the on/off switch (6) to turn the LED light (2) on.
• Briefly press the on/off switch to change the light mode:
Constant light → flashing light → SOS signal → constant light → ...
• To turn off the LED light, double-click the on/off switch again.
Carabiner
• Connect the carabiner to the eyelet (1) e.g. to fasten the product to a backpack.
• You can also hang the product on a suitable hook without the carabiner. Make sure that the
product does not fall.
Care and cleaning
• Disconnect the product from the connected devices before cleaning.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
damage the casing or cause the product to malfunction.
• This product does not contain any components that require maintenance. Never attempt to
open or disassemble it.
• Use a lint-free cloth to clean the product. Do not press too hard on the housing, as this can
lead to scratch marks.
100 %
• Dust can be easily removed using a soft and clean long-haired brush.
Solid blue
Disposal
Solid blue
Electronic devices are recyclable waste and must not be disposed of in the
Solid blue
household waste. Always dispose of the product according to the relevant statutory
Solid blue
regulations.
You thus fulfil your statutory obligations and contribute to the protection of the
environment.

Technical data

Input voltage/current ..................... 5 V/DC, 2 A
Output voltage/current .................. 5 V/DC, 3.4 A (total)
Rechargeable battery ................... LiPo, 16000 mAh
Solar charging current .................. 280 mA
Charge time .................................. approx. 10 h via USB
Colour temperature ....................... 9000-12000 K
Protection type .............................. IP67
Operating/storage temperature .... 0 to +45 °C
Dimensions (L x W x H) ................ 166 x 82 x 20 mm
Weight .......................................... 356 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE. *1661732_v2_0818_02_IPL_m_en