FARFISA INTERCOMS Mi 2401 Mode D'emploi page 5

Table 2 - System programming codes
Operating modes
mode 0 send floor call to other internal stations in parallel (1)
mode 1 button "1" deactivates all ring tones (2)
mode 2 button "1" deactivates all ring tones and button tones (2)
mode 3 button "1" does not deactivate ring tones and button tones (2)
mode 4 reserved; disabled
mode 5 the GC-GE terminals are activated upon call from external door station (3) disabled
mode 6 the GC-GE terminals are activated upon intercom call (3)
mode 7 reserved; disabled
(1) From the internal station connected to the floor call button (terminal A1) and with operating mode 0 enabled, the floor call is also sent to the other
apparatuses in parallel.
(2) If modes 1, 2 and 3 are disabled, press the button "1" for 4 seconds , without a conversation in progress, to deactivate the external and intercom
ring tones. To reactivate the ring tones, press the button "1" again for 4 seconds; you hear the confirmation tone.
(3) If modes 5 and 6 are disabled, the GC and GE terminals are activated to send the calls.
Example of system programming to enable operating mode 0 and 2 and to disable all the others operating modes
Operation
Call from external station.
When a call is made from the external station,
the intercom generates an acoustic tone and
stays ON for about 30 seconds. Pick up the
handset to start conversation with the external
station for about 90 seconds and press button
" " to open the door.
Connection with one or more external
stations without receiving the call.
Picking-up the handset when the system in
stand-by and no conversation in progress you
will hear the tone of system ready.
By pressing the button " " you will be
connected with the door station or, if more
than one door station is present in the system,
with the door station from which you received
the last call; in this case if the buttons from 1
to 6 have been programmed with the
addresses of the door stations present in the
system it would be possible to communicate
with them by pressing the associated buttons.
If picking up the handset you did not get any
tone, the system is busy (a communication
with another user is in progress), and no other
operations are allowed until the system
becomes free.
Making or receiving a call from another
user.
When the installation is in stand-by, you can
make a call to another user. You must have
stored the address of the desired user's in the
buttons 1÷6.
To make the call, pick up the handset, wait for
the free tone and press button. You will hear
the call tone and the intercom of the called
user will ring with a ring different from calls
from external stations or intercom calls from
the same apartment. If the called user answers
within 30 seconds, a 90-second conversation
starts, otherwise the system goes back to free.
The internal conversation in progress will be
automatically interrupted in case of call from
external station to any other user.
If you pick up the handset and receive no tone,
the installation is busy and you must wait until it
is free.
Making or receiving an intercom call in
your apartment.
When the installation is in stand-by, you can
make an intercom call to all intercom in the
same apartment (max 7 with internal address
from 000 to 006) by pressing buttons previously
programmed with code 000 (see table 3) .
To make the intercom call, pick up the handset,
wait for the free tone and press proper button.
After pressing the button you will get a calling
tone on the loudspeaker, while the intercom of
the called user rings with the programmed
melody. If the called user answers within 30
seconds, a 90-second conversation starts,
otherwise the system goes back to free.
The internal conversation in progress will be
automatically interrupted in case of call from
external station to any other user.
Default To enable
value press 1 time
button "2"
disabled enabled
disabled enabled
disabled enabled
disabled enabled
disabled -
enabled
disabled enabled
disabled -
Table 3. Button use for intercom calls of max. 7
intercoms in the same apartment.
Calling Intercom to call
intercoms CT0 CT1 CT2 CT3 CT4 CT5 CT6
CT0 (000) -
CT1 (001)
-
CT2 (002)
CT3 (003)
CT4 (004)
CT5 (005)
CT6 (006)
Button to press
(all programmed with code 000)
N.B.: The codes in parenthesis in the table are the
identification addresses of the internal stations that
were programmed previously (see chapter
"programming of the user address and internal
address" ).
Examples:
- From intercom CT1 (internal address 001) press
the button 1 for calls to intercom CT0.
- From intercom CT2 (internal address 002) press
the button 4 for calls to intercom CT4.
- From intercom CT4 (internal address 004) press
the button 4 for calls to intercom CT3.
To disable
press 2 times
button "2"
disabled
disabled
disabled
disabled
disabled
disabled
disabled
disabled
-
-
-
-
-
Mi 2401 - 8 -