Publicité
Les langues disponibles
Les langues disponibles
c -press the button
; an acknowledge tone
will be heard and the yellow LED lights-ON
continuously;
repeat phases a-b-c to program other buttons
or exit the programming mode by hanging up
the handset; yellow LED turns-OFF.
Notes.
- In each button can be stored only one code or
address.
- Intercom conversations or connections with
users and external stations of other buildings
will not be possible if digital exchanger art.2273
is installed.
Programming the number of ringing call
The intercom can receive 4 different calls that
can be changed as indicated in the procedure
below. The default programming values and the
call sequence are shown in table 1.
All programming operations must be carried out
with the handset in idle position.
Keep pressed the button "1" for more than 4
seconds; the yellow LED turns ON and you
hear the ring tone that was programmed for
calls from external door station.
a - Press the button "1" repeatedly to select the
ring tone.
b - Press the button "
" to confirm and go on
to select the number of rings.
c - Press the button "1" as many times as the
desired number of rings (once = 1 ring; 4 times
= 4 rings).
d - Press the button "
" to confirm and go on
to program the ring tone for intercom calls.
If you want to change the other two tone rings
(call from other user or floor call), you must
repeat steps a-b-c-d.
Pick up and close the handset for exit the
programming mode; yellow LED turns-OFF.
Adjusting the volume
With the handset in idle position, you can adjust
4 volume levels for all ring tones, as indicated
below:
press the button "1" for 4 seconds; the yellow
LED turns ON and you hear the external door
station ring tone;
hold the button "
" pressed and release it
when you hear the desired volume;
pick up and close the handset for exit the
programming mode; yellow LED turns-OFF.
The volume levels are stored and will be used for
the next calls.
More programming operations for
specific functions
How to program secondary user addresses
( additional programming operation that does
not depend on the programming operations of
user and internal station addresses)
The following programming operation allows you
to save 4 additional user addresses on the same
intercom (i.e.: exchanger function, intercom
To make the programming easier and to remind your self the stored codes, please fill in the following table
installed in common area with multiple users,
etc.).
N.B.: intercom must be programmed also with
the internal common address as specified in the
following.
To make the programming it is necessary:
enter the programming mode following the
instructions described in " Enter the
programming phase ";
keep pressed the button "
seconds; yellow LED starts flashing;
again keep pressed the button "
than 4 sec.; yellow LED starts quickly flashing;
enter the 3 digit of the 1st user secondary
address (codes from 1 to 200) following the
procedure reported on the paragraph
"Entering codes or addresses";
press the button "
" to confirm the present
address and move to the 2nd user address; an
acknowledge tone will be heard;
enter the 3 digit of the 2nd user secondary
address and confirm by pressing button "
proceed entering the 3rd and 4th secondary
user addresses consumer (if necessary) or to
press twice the "
" to pass to the insertion of
the internal common address;
enter the 3 digit that compose the internal
common address to the 4 new user
addresses (codes from 000 to 007) following
the procedure of the paragraph "Entering
codes or addresses".
Note: the internal common address has to be
unique and different from you address him
inside eventually programmed on other inter-
coms that has the same user address;
to press "
" to confirm and to return of choice
of programming; an acknowledge tone will be
heard and the yellow LED lights-ON continu-
ously;
pick up the handset for exit the programming
mode.
Note : If you want to make intercom calls, you must
program the call buttons with the codes of the
users you want to call.
Example
How to program three intercoms with user ad-
dresses 101, 102 and 103; from which user 103
should receive also calls addressed to user 101
and 102; user 101 and 102 should receive only
calls addressed to them.
- User 101 must be programmed only with user
address 101 and internal address 000.
- User 102 must be programmed only with user
address 102 and internal address 000.
- User 103 must be programmed with user ad-
dress 103, internal address 000, 1
nd
address 101, 2
secondary address 102, inter-
nal common address 001 being the internal
address of intercoms 101 and 102 already
programmed to 000.
System programming
The following programming allows you to
personalise the operation mode of button "1"
used to deactivate the ring tones and the GC-GE
terminals and send the floor call to the systems
with the same user address (internal stations in
parallel). See table 2.
To make the programming it is necessary:
enter the programming mode following the
" for more than 4
instructions described in " Enter the
programming phase ";
" for more
keep pressed the button "
seconds; yellow LED starts flashing;
a - keep pressed the button "1" for more than 4
seconds; yellow LED starts quickly flashing;
b - press the button "2" once to enable operating
mode 0 (you hear a sharp tone); within 2
seconds press the button "2" again to disable
operating mode 0 (you hear a low tone);
c - press the button "1" to confirm and proceed
to program the next mode;
";
you must repeat steps a, b and c to program all
operating modes in table 2;
after you have completed the operation and
confirmed operating mode 7 with the button
"1", press the button "
handset to exit the programming phase.
Note. Programming will not be changed if the
values of all modes are not entered correctly.
- Programming example of page 8.
Resetting the default programming values
To reset the intercom default programming val-
ues and delete all the variations made in the
programming mode you must:
enter the programming mode following the
instructions described in " Enter the program-
ming phase ";
press the buttons 6, 5, 4, 3, 2 and 1 succes-
sively; the tone indicates that the default values
have been restored.
Additional functions
Call floor
To have the floor call connect the apparatus as
illustrated in the diagram.
Call Repeat
You can connect the apparatuses as illustrated in
the diagram below to sent the intercom ring to
st
secondary
other locations in the house.
" for more than 4
" and replace the
Mi 2401
- 7 -
Publicité
