Publicité
Les langues disponibles
Les langues disponibles
PROGRAMMING
The intercom must be suitably programmed for
operation.
Two programming modes are available:
-automatic (quick programming of user code
acting from external station);
-manual (programming of all intercom functions)
The following programming is possible:
- user address;
- internal address;
- code to assign to buttons "1", "2", "3", "4", "5"
and "6" to make intercom calls or for special
services;
- selection of the call timing and call melody
for 4 different call melodies ( see table 1 ).
Factory setting
- user address
= 100
- internal address = 000
- buttons "1", "2", "3", "4", "5", "6" = no codes
are stored to the buttons
- number of call rings and call melody ( see
table 1 )
Table 1.
Factory setting for calls
Number Type of
Calls
of rings
from door station
1
intercommunicating
4
from other users
4
floor (local)
1
Attention: it is mandatory to program the
equipment only with the user code (address) all
other programming are optional.
Enter the programming phase
Hold the button
pressed for more than 4
seconds and pick up the handset after the
confirmation tone; the yellow LED turns on and
stays on for the entire programming selection
phase.
Release the button
.
If for 2 minutes no keys are pressed, system
switches back to the operating mode.
Exit the programming phase
You can exit the programming phase at any time
by replacing the
handset;
yellow LED turns-OFF.
Automatic programming
You can use the automatic programming mode
to save the intercom address from the external
station. To enter the automatic programming
mode you must:
enter the programming mode following the
instructions described in " Enter the
programming phase ";
make a call from an external station within
2 minutes. In case of installations with digital
push-button keyboard TD2100, key in the
number you want to assign to the intercom and
press "
". In case of installations with digital
encoder CD2131÷CD2138 press the button
you want to assign to the user on the push-
button keyboard. When the call is received, the
intercom is programmed automatically, you
hear the call tone in the handset. Close and
pick up the handset to start a conversation with
the external door station and check the correct
operation of the system; programming mode
is signalled on the external door station by an
acknowledge tone if accepted or a dissuasion
tone if rejected;
repeat programming phases for all the
intercoms connected to the system.
Manual programming
The manual programming mode allows you to
enter the user address, assign the internal address
and codes to numerical buttons (from 1 to 6).
Example of programming to page 12.
Using the push-buttons for programming
Press button "
addresses or codes.
: Press this button to confirm address or
code programming or go to the next
programming step.
1 : Press this button to confirm the digit just
dialled and to proceed to enter next digit in
the following order: hundreds, tens, units.
2 : Press this button to increase the value
you want to enter. Press the button for a
number of times equal to the digit you want
to enter (digit 1 = 1 time; digit 9 = 9 times;
digit 0 = 10 times).
Entering codes or addresses
melody
- Codes and/or addresses must have three digits
Din-Don
(hundreds, tens, units); codes and/or addresses
with tens and units or units only must be
Dring 1
completed by adding zeros. For example,
Dring 2
address 96 will become 096 and address 5 will
Dring 3
become 005.
- Digits must be entered individually (beginning
from the hundred), by pressing the button "2" for
a number of times "n", where "n" is the value of
the digit you want to enter. Store the digit pressing
the button "1"; a tone will confirm the acquisition
st
of the 1
digit.
- Follow the same procedure to store the 2nd
and 3rd digit.
For example , to enter code 096 you must:
- press button "2" 10 times to enter digit 0 and
press the button "1"; you will get a tone on the
loudspeaker;
- press button "2" 9 times to enter digit 9 and
press the button "1"; you will get a tone on the
loudspeaker;
- press button "2" 6 times to enter digit 6 and
press the button "1"; you will get a tone on the
loudspeaker.
Programming of the user address and
internal address
- User address – this code allows you to receive
an external call, have a conversation and open
the door at the calling external station.
- Internal address – these codes are used to
identify the intercoms installed in the apartment
(max.7). In case of one intercom only, the internal
code must be 000 (default value); if other
intercoms are present (max. other 6) you must
assign to them the codes 001, 002, 003 etc.
Programming these addresses all the
intercoms will ring-UP when receiving an
external, intercommunicating or floor (local) call
( if programmed ).
To program the user address and internal
address it is necessary to:
", "1" and "2" to enter
Note. If one of the two above mentioned
addresses is already correctly programmed and
you don't want to program it again it would be
possible to skip its programming by simply
pressing button
Programming address to be stored to each
button
Buttons 1, 2, 3, 4, 5 and 6
These buttons can be used to:
To make the programming it is necessary:
enter the programming mode following the
instructions described in " Enter the
programming phase ";
keep pressed the button
for more than 4
seconds; yellow LED starts flashing;
enter the 3 digit of the user address following
the procedure reported on the paragraph
"Entering codes or addresses";
press the button
to confirm the present
phase and move to the next phase which is:
programming of the internal address; an
acknowledge tone will be heard;
enter the 3 digit of the internal address
following the procedure reported on the
paragraph "Entering codes or addresses";
press the button
to confirm; an acknowl-
edge tone will be heard and the yellow LED
lights-ON continuously;
proceed with another programming phase or
exit the programming phase by hanging up the
handset.
.
.
make intercommunicating calls;
- to call users of different apartments it is
necessary to store in each button of your
intercom the address of the user you wish to
call pressing that button (codes from 001 to
200).
- to call other intercoms installed in the same
apartment (local intercommunicating service),
it is necessary to store in the buttons 1, 2, 3, 4,
5, 6 of each intercom always the code 000;
starting from button 1 and going on until you
have programmed, with the code 000, as
many buttons as are the intercoms installed in
the apartment you wish to call; automatically
by pressing buttons of one unit you will call the
unit whose internal address is related to the
pressed button according to table 3.
For example if you press the button 3 from the
intercom whose intercommunicating address
is 002 you will call the user with intercom-
municating address 003.
monitoring external door stations; to
enable this feature store the address of the
external door station (codes from 231 to 250).
optional functions operated by means of
the actuators art.2281; to enable this functions
store the address of the actuator to be operated
(codes from 211 to 220).
enter the programming mode following the
instructions described in " Enter the
programming phase ";
a - keep pressed for more than 4 seconds the
button you wish to program; yellow LED starts
flashing;
b -enter the 3 digit of the code or address you
wish to store following the procedure reported
on the paragraph "Entering codes or
addresses";
Mi 2401
- 6 -
Publicité
