Remaining Hazards; Product Specifications; Technical Data - F.F. Group AC-B 90/4MC PRO Notice Originale

AC-B 90/4MC PRO | AC-B 150/4MC PRO
Check for correct alignment of moving parts or
other failures that could be a source of danger. A
damaged guard or other part should be replaced by
an authorized service center before operating the
machine.
NOISE AND VIBRATION HAZARDS
The noise levels shown in these instructions are
the maximum levels for use of the machine. Insuf-
ficient maintenance has a significant impact on
vibration and noise emissions. Consequently, it is
necessary to take preventive steps to eliminate
possible damage due to high levels of noise and
stress from vibration. Maintain the machine well,
wear ear protection devices, anti-vibration gloves
and take breaks while working.
WORKING AREA HAZARDS
Thoroughly inspect the whole work area and use a
rake or yard brush to manually loosen debris and
remove anything that could be a hazardous source
to you or cause damage to the machine. Keep work
area clean and tidy. Do not operate the machine in
wet environment conditions or when the machine
itself is wet. Keep the machine away from flamma-
ble material. Check that there are no bystanders,
animal or items that could be damaged within the
machine's range of action. Work only in daylight,
or with suitable artificial light, in good visibility
conditions. Try not to cause any noise disturbance,
by only using this machine at reasonable times of
the day. Take on a firm and well-balanced position.
Where possible, avoid working on wet, slippery
ground or in any case on uneven or steep ground
that does not guarantee stability for the operator.
Storing of tools that are not in use should be done
in a dry and safe place away from the operating ma-
chine and out of the reach of children.

REMAINING HAZARDS

The machine was built using modern technology
and in accordance with recognized safety rules.
Even when all safety measures are in place, some
remaining hazards, which are not yet evident, may
be present. The operator should use common
sense and take necessary precautions to avoid risk
due to remaining hazards.

PRODUCT SPECIFICATIONS

INTENDED USE
This machine is designed and manufactured for
short term storage of high pressure air.
Any other use differing from the above-mentioned
ones could be hazardous, harm people and/or dam-
age things and the machine itself.
IMPROPER USE
The machine must not be used for hazardous mate-
rials, e.g. accumulation of inflammable or explosive
products and any other object that could be dan-
gerous to the machine itself as well as the opera-
tor, bystanders, animals or property.
Other examples of improper use may include, but
are not limited, to operation of the machine:
Without the original accessories supplied by the
f
manufacturer.
With original accessories but in a way not in ac-
f
cordance to the instructions.
Without original spare parts.
f
With unauthorized modifications.
f
NOTE
According to the applicable product liability laws,
the manufacturer of the device does not assume lia-
bility for damages to the product or damages caused
by the product that occurs due to:
Improper handling no complied with the operat-
f
ing instructions.
Repairs by third parties and not by authorized ser-
f
vice technicians.
Installation of non-original spare parts.
f
Non-intended use.
f
Electrical system breakdown due to power of the
f
machine in a manner not compliant with the elec-
tric and VDE regulations.

TECHNICAL DATA

Article Number
Model
Rated voltage
Rated frequency
Motor type
Motor power
Rated speed min
Number of
cylinders
Cut-in pressure
Cut-off pressure
Tank capacity
Weight
Sound emission values
Typically the A-weighted noise levels of the pro-
duct are:
Sound pressure
dB(A)
level (LpA)
Sound power
dB(A)
level (LwA)
Uncertainty (K)
English |
46 589 46 590
AC-B AC-B
90/4MC 150/4MC
PRO PRO
V 220 - 240 220 - 240
Hz 50 50
2 pole 2 pole
hp 4 4
2.850 2.850
-1
1 1
PSI 115 115
PSI 145 145
L 90 150
kg 67 85
73,4 73,4
97,0 97,0
dB 3,0 3,0
www.ffgroup-tools.com
9