Battery Charger Safety; Product Familiarisation; Intended Use - Silverline 263630 Traduction Des Instructions Originales

GB
s) The power tool will draw in dust through the vents on its body. Excessive
accumulation of powdered metal may cause an electrical hazard and destroy the tool.
ALWAYS ensure the environment dust level is safe for the tool and ensure the vents are
not blocked.
t) For mains-operated power tools, ensure the cable of the power tool is ALWAYS
kept behind the tool and never close to where the accessory or blade is operating.
u) DO NOT reach under the workpiece, rest the workpiece on your body, or hold the
workpiece while working on it, as contact with the blade or accessory protruding
from the workpiece can result in serious injury.
v) Anti-vibration gloves should be worn when operating power tools that produce
large amount of vibration, especially during long-term use.
w) For power tools with a rotating mechanism and accessories ensure the operator
is not wearing clothes or gloves with frayed threads, cords etc. that could be
entangled inthe rotating mechanism dragging the operator's hand into the
rotating accessory causing injury. ALWAYS wear tight fitting work clothes, safety
shoes. Remove jewellery and secure long hair. NEVER wear fabric-based gloves that can
produce strands of material when operating this type of power tool.
x) DO NOT allow sanding sheets to wear away on the sanding pad. This will damage
the surface of the pad requiring replacement and may cause parts of the sanding sheet
to fly off the pad, causing operator injury.
y) DO NOT touch the moving sanding sheet.
z) Wire brush bristles are thrown by the brush even during ordinary operation.
DO NOT overstress the wires by applying excessive load to the brush. The wire bristles
can easily penetrate light clothing and skin.
Note: The tool must ONLY be used for its intended purpose. Any use other than those
mentioned in this manual will be considered a case of misuse. The operator, and not the
manufacturer, shall be liable for any damage or injury resulting from such cases of misuse.
The manufacturer shall not be liable for any modifications made to the tool, nor for any
damage resulting from such modifications.

Battery Charger Safety

Use the battery charger correctly
• Refer to the section of this manual relating to use of the battery charger before
attempting to charge the battery.
• DO NOT attempt to use the charger with any batteries other than those supplied. Keep
your battery charger clean; foreign objects or dirt may cause a short or block air vents.
Failure to follow these instructions may cause overheating or fire
• If the supply cord is damaged, it must be replaced by the manufacturer, the service
agent or similarly qualified persons in order to avoid a hazard
WARNING: DO NOT attempt to recharge non-rechargeable batteries.
Battery Safety
WARNING: Li-Ion batteries, if incorrectly used, stored or charged are a fire, burn and
explosion hazard.
• Keep the battery out of reach of children
• ONLY charge Li-Ion batteries using the charger provided or designed specifically for
your product
• ONLY use Li-Ion batteries provided with a product or specifically designed to be
compatible
• Allow batteries to cool for 15 minutes after charging or heavy use. Failure to follow
these instructions may cause overheating or fire
• When not in use batteries should be stored at room temperature (approximately 20˚C)
• Ensure that battery contacts cannot accidentally short in storage. Keep batteries clean;
foreign objects or dirt may cause a short. Keep away from other metal objects, for
example paperclips, coins, keys, nails and screws
• Under abusive conditions, liquid may be ejected from the battery. This liquid may cause
skin irritation or burns. Avoid contact. If contact accidentally occurs, flush with water. If
liquid contacts eyes, seek medical help
• DO NOT open, disassemble, crush, heat above 60°C or incinerate. Do not dispose of in
fire or similar
6 6

Product Familiarisation

1 Blade
2 Work Light LED
3 On/Off Switch
4 Variable Speed Dial
5 Hand Grip
6
Battery
7 Battery Release
8 Motor Vents
9 Mounting Spindle
10 Mounting Washer
11 Mounting Bolt
12 Battery Charger
13 Mains Plug
14 Green LED
15 Red LED
16 Sanding Pad
Included accessories (not shown):
Blow-moulded case, hex key, 1x scraper, 4x sanding sheets (40, 80, 120 and 240 grit)

Intended Use

Battery operated oscillating multi-tool designed for light to medium duty cutting and
abrasive tasks by fast oscillation of a blade, file or sanding pad.
Unpacking Your Tool
• Carefully unpack and inspect your new sander. Familiarise yourself with all its features
and functions
• Ensure that all parts of the tool are present and in good condition. If any parts are
missing or damaged, have such parts replaced before attempting to use this tool
Before Use
WARNING: ALWAYS wear suitable cut-proof gloves when handling blades or other sharp
accessories.
Removing a battery
• To remove the Battery (6) from the Multi-Tool, press the Battery Release (7), then slide
the Battery off the Hand Grip (5)
WARNING: DO NOT try to remove the Battery without pressing the Battery Release button.
The drill or Battery could be damaged.
Fitting a battery
1. To fit a charged battery, slide it into the Hand Grip (5) of the drill until it clicks and
locks into position
Note: Make sure the Battery and Multi-Tool are lined up correctly. If the Battery does not
slide into the Multi-Tool easily, don't force it. Instead, slide the Battery out of the Multi-Tool
again, check the top of Battery and the Multi-Tool battery slot are clean and undamaged
and that the contacts are not bent.
Setting up the battery charger
1. If fitted, remove any battery from the Battery Charger (12)
2. Insert the Mains Plug (13) into a suitable mains socket
Note: The Green LED (14) on the Battery Charger will illuminate to indicate that the charger
is ready to charge the battery.
WARNING: ONLY use this charger to charge the supplied battery or additional purchased
batteries that are specifically designed for this tool.
WARNING: The charger is designed for indoor use only, and MUST NOT be used in damp
or wet conditions.