Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
The noise and vibration values were developed using a
standardised measuring process.
Sound pressure L
pA
Sound power L
wA
Uncertainty K
WA
Vibration
A
hv
Uncertainty K
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Reduce noise generation and vibration to a minimum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
• Wear gloves
Before starting the equipment
Unpack the device and check it for complete delivery con-
tents and transport damage.
NOTE
The batteries (optional; depending on the delivery scope)
are not fully charged on delivery. Before first use, fully
charge the batteries. See charger instruction manual.
Removing / inserting the battery(Abb.2)
1.To remove the battery (3) from the appliance, press the
release button (13) on the battery and pull out the bat-
tery.
2. To insert the battery (3), place it on the guide track and
push it back into the appliance. It will audibly snap
Use
Height adjustment (Abb. 3)
Undo the union nut (4) until the grass trimmer handle can be
moved in and out freely. Now set the required working height
and secure the handle in this position by tightening the union
nut again.
Adjusting the additional handle (Abb. 4)
Undo the adjustment lock for the additional handle until it can
be moved forwards and backwards without any great resistance.
Set the required position and tighten the securing screw again.
Operation
To obtain maximum performance from your grass trimmer,
please follow these instructions:
Never use the grass trimmer without the guard.
•
•
Do not mow grass when it is wet. The best results are
achieved with dry grass.
•
Do not allow the grass trimmer near the grass until the
switch is pressed, i.e. the grass trimmer is in operation.
•
To cut properly, swing the machine sideways while mov-
ing forwards. Keep the grass trimmer inclined at an angle
of approx. 30° while you do so .
If the grass is long, the grass must be cut shorter in stag-
•
www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
72,4 dB(A)
87,4 dB(A)
3 dB(A)
1,45 m/s²
1,5 m/s²
in.
es, starting from the tip.
•
Use the guard hood to prevent unnecessary wear.
•
To avoid unnecessary wear, keep the grass trimmer away
from hard
objects.
Turning on/off (Fig. 1)
•
In order to turn your lawn trimmer on, press the dead
man switch (1) and the on/off switch (2
•
Always have one hand on the auxiliary handle (12).
•
In order to turn the lawn trimmer off, release the on/
off switch (2).
Using the grass trimmer as an edge trimmer
(Abb.5/6)
To cut the edges of lawns and fl ower beds, the grass trim-
mer can be converted as follows:
• Remove the battery pack
• Fold the edge guide (9) upwards.
• Push the locking button (5) upwards.
• Turn the motor head through 90° in the required direc-
tion until it latches in place(Abb.5).
• You can convert your lawn trimmer into an edge trimmer
this way and carry out vertical cutting of the lawn.
• When edge trimming, use the device's two guide wheels
(Fig. 6/Pos. 6+10).
• To convert the equipment back to its original state, pro-
ceed in reverse order.
Extending the cutting thread
Warning! Do not use metal wire or plastic-coated metal
wire of any kind in the spool. This can lead to severe injuries
to the user.
To extent the cutting thread, keep the device running and
tap the spool on the ground. The thread will be extended
automatically. The blade on the safety screen shortens the
thread to the approved length.
Replacing the cutting thread (Fig. 7-9)
•
Hold on to the casing (f) and, at the same time, turn the
lid (g) anti-clockwise and remove it.
Remove the casing spool (h) and spring.
•
•
Replace the thread (i), insert the spool (h) and spring,
and, at the same time, pull the thread through the open-
ing. Replace the lid (g) by turning it clockwise and hold-
ing on to the casing
(f).
Sharpening the cutting blade (Fig. 6)
Loosen the cutting blade's (l) cross-head screws (k) from
•
the protective hood (7).
•
Put the cutting blade (l) into a vice.
•
Using a flat file, sharpen the edge of the cutting blade (l)
Make sure that the original cutting angle is maintained.
•
Fix the cutting blade (l) back onto the protective hood
•
(7).
Cleaning and maintenance
Before putting away or cleaning the grass trimmer,
switch off and remove the battery pack.
CLEANING
•
Regularly check the device before starting work
Damaged parts have to be repaired or replaced by an
•
authorised service department before you can work
with the device
•
Only ever use original accessories and spare parts.
Use the device only with batteries and chargers intended
•
for it.
Do not use the charger if it is damaged.
•
15 І 56
Publicité
Table des Matières
