Before Starting The Equipment; Attachment And Operation - Scheppach BCH3200PB4 Traduction Des Instructions D'origine

7. Before starting the equipment

Each time before use, check the following:
• That there are no leaks in the fuel system.
• That the equipment is in perfect condition and that
the safety devices and cutting devices are complete.
• That all screws are securely fastened.
• That all moving parts move smoothly.
m CAUTION!
The engine does not come with oil in it. Therefore, ensure
that you add 0,08 liters of oil before starting it up. Use nor-
mal, multigrade oil (SAE30 / 10W30). The oil level in the
engine must be checked each time before mowing. Fig.
44 - 45
You will also need to fill in petrol, as this is also not sup-
plied upon delivery.
1 Fuel
Recommended fuels.
Normal petrol / Lead free max. 5% bioethanol
Important: Only use containers designed and approved
for the purpose to transport and store fuel.
Warning!
Take care of the emission of exhaust gases.
Always shut off engine before fueling. Never add fuel
to a machine with a running or hot engine. Take care
of fire!

8. Attachment and operation

ASSEMBLY
When assembling this machine, please follow the in-
structions for assembly printed.
1 Assemble the handle on the machine. Fig. 4 -6
• Assemble the bike type handle on the machine: First
release the inner hex screws, second take right and
left handle on the centre of handle holder.
• Last assemble the handle holder and tighten the inner
screws enough.
2. Mounting the shaft. Fig. 7
• Push the lower part of the shaft (b) right down until the
stop pin (a) slots into the hole (c) in the shaft. This is
easier to do if you rotate the bottom of the shaft (b)
slightly in both directions. The pin (a) is in place when
it is completely lodged in the hole.
• Lastly, tighten the knob (d) securely.
3. Assemble the safe guard. Fig. 11 13
• Fix the safe guard with hex key and wrench enclosed
as stardard accessories for tighting the nuts enough.
Please see the below pictures showing.
m Warning! Use only original manufacturer's replace-
ment parts, accessories and attachments. Failure to do
so can cause poor performance, possible injury and may
void your warranty. Never use the machine without the
guard assembled!
24 GB
4. Assemble and disassemble the cutting head
grass trimmer / nylon cutting head. Fig. 14 - 15
• Release the nut.
Line up the two holes of flange and shield, use one
screw driver to hold the flange as below and turn the
socket wrench clockwise, the nut will be released.
• Fit the Nylon cutting head.
Remove another shield after release the nut. Still hold
the flange, take the Nylon cutting head on the shaft
and rotate counter-clockwise, the Nylon cutting head
is fitted. Fig. 15
• Release the Nylon cutting head. Fig. 10
Use screw driver to hold flange and then rotate the
Nylon cutting head clockwise, it will be replaced.
Brush cutter / Cutter blade
• Fit the blade. Fig. 8 - 10
Take the outer flange off after release the nut, then
put the blade (4), outer flange (25), shield (24) and
nut according to priority as below picture. Note the
blade rotation direction needs be same as below pic-
ture. Use screw driver to hold flange and tighten nut
counter-clockwise, ensure the nut is tightened enough.
• Release blade. Use screw driver to hold flange and
release nut, the blade can be took off.
m Warning!
Please make sure the cutting head has been assembled
correctly before use!
Note: The packaging material is made of recycle ma-
terials. Dispose of packaging materials in accordance
with regulations.
5. Fit the belt. Fig. 17 - 21
• to picture showing, fit the belt well.
OPERATION
When working with the equipment, the appropriate plas-
tic guard hood for cutting blade mode or cutting line
mode must be fi tted to prevent objects being thrown
out by the equipment.
The integrated blade in the cutting line guard hood au-
tomatically cuts the line to the optimum length. Fig. 16
Filling with fuel
m Danger of injury! Fuel is explosive!
Turn off and cool the motor down before filling
the tank with fuel. You must observe all safety
instructions relating to handing fuel.
m Risk of device damage!
The device is supplied without motor or gearbox
oil.
ATTENTION! Before operating, you must fill it
with fuel.
• Unscrew the tank cap (14) and remove it. Fig. 1
• Pour in the fuel carefully. Avoid spilling!
• Screw the tank cap on firmly by hand.