Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Installation
5
5.2.2 Évacuation à l'extérieur par
l'arrière (conduit horizontal de
type B)
3/8" TO EDGE
12"
TO
NOTE: IT IS VERY IMPORTANT
THE DIRECTIONS
READ AND FOLLOW
INSTRUCTION S
IN THE INSTALLATION
WITH THIS
BEFORE PROCEEDING
REAR WALL TEMPLATE.
4"
serves to position the bottom
This Rear Wall Template
the horizontal exhaust
mounting plate and to locate
outlet.
1. Use a level to check that
the template is positioned
accurately.
one stud on the left or
2. Locate and mark at least
right side of the centerline.
It is important to use at
least one wood
a stud to support the weight
screw mounted firmly in
two additional, evenly spaced
of the microwave. Mark
locations for the supplied
toggle bolts.
locations. Where there is
3. Drill holes in the marked
for wood screws. For holes
a stud, drill a 3/16" hole
stud, drill 5/8" holes for
that do not line up with a
toggle bolts.
MOUNTING PLATE
DO NOT INSTALL THE
AT THIS TIME.
from the rear wall.
4. Remove the template
book for your
5. Revie
w
h t
e Installation Instruction
installation situation.
Darle vuelta a la hoja
para consultar la
versión en Español.
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
STUD ON EITHER SIDE
OF
LOCATE AT LEAST ONE
THE CENTERLINE.
EVENLY
MARK THE LOCATION
FOR 2 ADDITIONAL,
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
along the dotted line.
Trim the rear wall template
Vue d'ensemble de l'installation
B1. Préparation du mur arrière
B2. Retrait de la plaque du ventilateur
B3. Fixation de la plaque de montage au mur
B4. Préparation de l' a rmoire supérieure
B5. Ajustement du ventilateur
B6. Installation du four à micro-ondes
Assurez-vous que les vis du moteur
du ventilateur et de la plaque du
A
ventilateur sont correctement ser-
rées lorsque vous les remettez en
place. Cela permet d' é viter des vibra-
tions excessives.
Assurez-vous que le câblage du mo-
A
teur a été effectué et correctement
fixé, et que les câbles ne sont pas
coincés.
54 / 63 FR
Four à micro-ondes à convection à hotte intégrée / Manuel d'installation
Trim the rear wall template
along the dotted line.
Locate and mark holes
to align with holes in the
t a
. e
m
o
u
t n
n i
g
l p
IMPORTANT:
STUD ON EITHER SIDE
OF
LOCATE AT LEAST ONE
THE CENTERLINE.
FOR 2 ADDITIONAL,
EVENLY
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
B1. Préparation du mur arrière pour
l'évacuation à l'extérieur par l'arrière
Vous devez percer une ouverture dans le mur ar-
rière pour l' é vacuation à l' e xtérieur.
NOT E:
IT IS VER
REA D
AND FOLL
Y IMPO
RTAN
IN THE
OW THE
T TO
BEFO
INST AL
L
DIRE CTIO
RE PRO
A
T
I
O
N
I
N
NS
REA R
WAL L
CEE DING
S
TRUC
TION S
TEM PLAT
WITH
This Rear
Wall Templa
E.
THIS
3/8" TO EDGE
mounti
ng plate
te serves
outlet.
and to
to positio
12"
1. Use
locate the
horizon
n the bottom
a level
to check
tal exhaus
accura
tely.
that the
t
2. Locate
and mark
templa
te is positio
right side
at least
ned
of the centerl
one stud
on the
4"
screw mounte
It is importa
ine.
left or
d firmly
nt to use
at least
of the microw
in a stud
one wood
locatio ns
ave. Mark
two additio
to suppor
3. Drill
holes in
for the
supplie
nal, evenly
t the weight
a stud,
the marked
d toggle
bolts.
spaced
drill a 3/16"
locatio ns.
that do
not line
hole for
wood screws
Where
there is
toggle
bolts.
up with
a stud,
drill 5/8"
. For holes
AT THIS
DO NOT
INSTA LL
holes for
4. Remov
TIME.
THE MOUN
e the templa
TING PLATE
5. Review
the Installa
te from
installa
tion situatio
tion Instruc
the rear
wall.
n.
tion book
for your
Darle vuelta
versió n
a la hoja
en Españ
para consu
ol.
ltar la
Loca te
and mark
moun ting
holes to
plate .
align with
IMPO RTAN
holes in
T:
the
LOC ATE
AT LEAS
THE CEN
T ONE
TERL INE.
STUD
MAR K
THE LOC
ON EITH
SPAC
ATIO N
ER SIDE
ED TOG
FOR 2
OF
ARE A.
GLE BOLT
ADD ITION
S IN THE
AL, EVEN
MOU NTIN
LY
G PLAT
E
Trim the
rear wall
temp late
alon g
the dotte
d line.
Loca te
and mark
moun ting
plate .
IMPO RTAN
T:
LOC ATE
AT LEAS
THE CEN
MAR K
TERL INE.
THE LOC
SPAC
ED TOG
ARE A.
• Lisez les instructions relatives au GABARIT
POUR MUR ARRIÈRE.
• Collez-le au mur arrière avec du ruban adhésif,
en l' a lignant sur les trous préalablement percés
pour les trous A et B de la plaque de montage.
• Percez l'ouverture conformément aux
instructions sur le GABARIT POUR MUR ARRIÈRE.
Trim the
rear wall
temp late
alon g
the dotte
d line.
holes to
align with
holes in
the
T ONE
STUD
ON EITH
ER SIDE
ATIO N
OF
FOR 2
GLE BOLT
ADD ITION
S IN THE
AL, EVEN
MOU NTIN
LY
G PLAT
E
Publicité
Chapitres
Table des Matières
