Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Installation
5
5.1 Placement of the
mounting plate
5.1.1 Removing the microwave
oven from the carton/ removing
the mounting plate
1. Remove the installation instructions, filters,
glass tray and the small hardware bag. Do not
remove the Styrofoam protecting the front of
the oven.
2. Fold back all 4 carton flaps fully against carton
sides. Then carefully roll the oven and carton
over onto the top side. The oven should be
resting in the Styrofoam.
Styrofoam
3. Pull the carton up and off the oven.
4. Cut the middle of the outer protective plastic
bag to remove the mounting plate
Screws
Mounting Plate
14 / 63 EN
Carton
Screws
Over The Range Convection Microwave Oven / Installation Manual
5. Remove the screws from the mounting plate.
This plate will be used as the rear wall template
and for mounting. Reinstall the screws into the
holes where they were removed.
5.1.2 Finding the wall studs
1. Find the studs, using one of the following
methods:
• Stud finder – a magnetic device which locates
nails.
• Use a hammer to tap lightly across the mounting
surface to find a solid sound. This will indicate a
stud location.
2. After locating the stud(s), find the center by
probing the wall with a small nail to find the
edges of the stud. Then place a mark halfway
between the edges. The center of any adjacent
studs should be 16
"
from this mark.
3. Draw a line down the center of the studs.
A
WARNING: The microwave must
be connected to at least one wall
stud.
5.1.3 Determining wall plate
location under your cabinet
Plate position—beneath at bottom
cabinet
NOTE:
IT IS VERY
READ
AND FOLLO
IMPOR
IN THE
W THE
TANT
TO
BEFOR
INSTAL
LATION
DIRECT
REAR
E PROCE
EDING
INSTRU
CTIONS
IONS
This Rear
WALL
TEMPL
WITH THIS
3/8" TO EDGE
mounting
Wall Template
ATE.
12"
outlet.
plate and
to locate
serves
to position
1. Use
a level
the horizontal
the bottom
accurately
to check
.
that the
exhaust
2. Locate
and mark
template
is positioned
right side
of the centerline
at least
one stud
on the left
4"
screw mounted
It is important
.
or
of the microwave
firmly in
to use at
a stud to
least one
locations
for the supplied
. Mark two
support
wood
the weight
3. Drill holes
in the marked
toggle bolts.
additional
, evenly
spaced
Trim the
rear wall
that do
a stud,
drill a 3/16"
locations.
toggle bolts.
not line
up with
hole for
wood screws.
Where
there is
a stud,
drill 5/8"
holes for
For holes
AT THIS
DO NOT
TIME.
INSTALL
4. Remove
the template
THE MOUNTIN
G PLATE
5. Review
the Installation
from the
installation
situation.
Instruction
rear wall.
book for
your
Darle vuelta
versión
a la hoja
en Español.
para consultar
la
Locate
mountin
and mark
holes to
g plate.
align with
IMPOR
TANT:
holes in
the
LOCAT
E AT LEAST
THE CENTE
ONE STUD
MARK
RLINE.
ON EITHER
THE LOCAT
SIDE OF
SPACE
D TOGGL
ION FOR
2 ADDITI
AREA.
E BOLTS
ONAL,
IN THE
MOUNT
EVENL
Y
ING PLATE
Trim the
rear wall
templa
te along
the dotted
line.
Locate
and mark
mountin
holes to
IMPOR
g plate.
align with
holes in
LOCAT
TANT:
E AT LEAST
THE CENTE
ONE STUD
MARK
THE LOCAT
RLINE.
ON EITHER
SPACE
ION FOR
AREA.
D TOGGL
E BOLTS
2 ADDITI
IN THE
ONAL,
MOUNT
C L
Draw a vertical line on the wall at the center of the
30 ʺ wide space. Tape the Rear Wall Template
onto the wall matching the centerline and touching
the bottom of the cabinet.
(40.6 cm) or 24
(61 cm)
"
templa
te along
the dotted
line.
16-1/2
the
SIDE OF
EVENL
ING PLATE
Y
Publicité
Chapitres
Table des Matières
