Outside Back Exhaust (Horizontal Duct); Installation Overview - Blomberg BOTR30200CSS Manuel D'installation

Four à micro-ondes à convection à hotte intégrée
Masquer les pouces Voir aussi pour BOTR30200CSS:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Installation
5
5.2.2 Outside back exhaust
(horizontal duct type B)
3/8" TO EDGE
12"
TO
NOTE: IT IS VERY IMPORTANT
THE DIRECTIONS
READ AND FOLLOW
INSTRUCTION S
IN THE INSTALLATION
WITH THIS
BEFORE PROCEEDING
REAR WALL TEMPLATE.
4"
This Rear Wall Template
serves to position the bottom
the horizontal exhaust
mounting plate and to locate
outlet.
1. Use a level to check that
the template is positioned
accurately.
one stud on the left or
2. Locate and mark at least
right side of the centerline.
It is important to use at
least one wood
a stud to support the weight
screw mounted firmly in
two additional, evenly spaced
of the microwave. Mark
locations for the supplied
toggle bolts.
3. Drill holes in the marked
locations. Where there is
for wood screws. For holes
a stud, drill a 3/16" hole
stud, drill 5/8" holes for
that do not line up with a
toggle bolts.
DO NOT INSTALL THE
MOUNTING PLATE
AT THIS TIME.
4. Remove the template
from the rear wall.
e Installation Instruction
book for your
5. Revie
w
h t
installation situation.
Darle vuelta a la hoja
para consultar la
versión en Español.
Locate and mark holes
to align with holes in the
mounting plate.
IMPORTANT:
STUD ON EITHER SIDE
OF
LOCATE AT LEAST ONE
THE CENTERLINE.
EVENLY
MARK THE LOCATION
FOR 2 ADDITIONAL,
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
along the dotted line.
Trim the rear wall template

Installation overview

B1. Prepare Rear Wall
B2. Remove Blower Plate
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
Make sure the screws for the blower
A
motor and blower plate are securely
tightened when they are reinstalled.
This will help to prevent excessive
vibration.
A
Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
Over The Range Convection Microwave Oven / Installation Manual
along the dotted line.
Trim the rear wall template
to align with holes in the
Locate and mark holes
n i
g
l p
t a
. e
m
o
u
t n
IMPORTANT:
STUD ON EITHER SIDE
OF
LOCATE AT LEAST ONE
THE CENTERLINE.
FOR 2 ADDITIONAL,
EVENLY
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
B1. Preparing the rear wall for out-
side back exhaust
You need to cut an opening in the rear wall for out-
side exhaust.
NOT E:
REA D
IT IS VER
AND FOLL
Y IMPO
IN THE
OW THE
RTAN
T TO
BEFO
INST AL
DIRE CTIO
RE PRO
L
A
T
O
I
N
I
NS
REA R
CEE DING
N
S
TRUC
WAL L
TEM PLAT
WITH
TION S
This Rear
E.
THIS
3/8" TO EDGE
mounti
ng plate
Wall Templa
outlet.
and to
te serves
to positio
12"
1. Use
locate the
n the bottom
a level
to check
horizon
tal exhaus
accura
tely.
that the
t
2. Locate
and mark
templa
te is positio
right side
at least
ned
of the centerl
one stud
4"
It is importa
ine.
on the
left or
screw mounte
nt to use
of the microw
d firmly
in a stud
at least
one wood
locatio ns
ave. Mark
to suppor
3. Drill
for the
supplie
two additio
nal, evenly
t the weight
a stud,
holes in
the marked
d toggle
bolts.
spaced
drill a 3/16"
locatio ns.
that do
not line
hole for
Where
toggle
bolts.
up with
wood screws
there is
a stud,
drill 5/8"
. For holes
AT THIS
DO NOT
INSTA LL
holes for
TIME.
THE MOUN
4. Remov
e the templa
TING PLATE
5. Review
te from
installa
the Installa
tion Instruc
the rear
tion situatio
tion book
wall.
n.
for your
Darle vuelta
versió n
a la hoja
en Españ
para consu
ol.
ltar la
Loca te
and mark
moun ting
holes to
IMPO RTAN
plate .
align with
holes in
LOC ATE
T:
the
AT LEAS
THE CEN
T ONE
TERL INE.
STUD
MAR K
THE LOC
ON EITH
ER SIDE
SPAC
ED TOG
ATIO N
FOR 2
OF
ARE A.
GLE BOLT
ADD ITION
S IN THE
AL, EVEN
MOU NTIN
LY
G PLAT
E
Trim the
rear wall
temp late
alon g
the dotte
d line.
Loca te
and mark
moun ting
plate .
IMPO RTAN
T:
LOC ATE
AT LEAS
THE CEN
TERL INE.
MAR K
THE LOC
SPAC
ED TOG
ARE A.
• Read the instructions on the REAR WALL
TEMPLATE.
• Tape it to the rear wall, lining up with the holes
previously drilled for holes A and B in the wall
plate.
• Cut the opening, following the instructions of
the REAR WALL TEMPLATE.
Trim the
rear wall
temp late
alon g
the dotte
d line.
holes to
align with
holes in
the
T ONE
STUD
ON EITH
ER SIDE
ATIO N
FOR 2
OF
GLE BOLT
ADD ITION
S IN THE
AL, EVEN
MOU NTIN
LY
G PLAT
E
23 / 63 EN

Publicité

Chapitres

Table des Matières
loading

Table des Matières