Makita DVC865L Manuel D'instructions page 11

Locking or unlocking the caster
► Fig.8: 1. Caster 2. Stopper lever 3. FREE position
4. LOCK position
Locking the caster is convenient when storing the
cleaner, stopping the work on the way and keeping the
cleaner still.
To operate the stopper, move it by hand.
To lock the caster with a stopper, lower the stopper
lever and the caster no longer will rotate. To release the
caster from the locked position, raise the stopper lever.
NOTE: When moving the cleaner, make sure that
the caster is unlocked. Moving the cleaner with the
caster in the locked position may cause damage to
the caster.
Carriage handle
When carrying the cleaner, carry it by holding the han-
dle on the head. The handle is retractable at the head
when not in use.
► Fig.9
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
CAUTION:
Always wear dust mask during
assembly or maintenance.
Installing the powder filter (HEPA)
and prefilter (for dry dust)
Optional accessory
CAUTION:
Never pick up water or other liq-
uids or wet dusts when using the powder filter.
Picking up such things may cause the powder filter
breakage.
To use powder filter:
1.
Remove the float cage and float by removing the
bolts.
► Fig.10: 1. Float 2. Float cage
2. Place the prefilter in the tank while aligning the
mounting position markings.
3. Mount the damper on the powder filter and then
place them in the prefilter while aligning the mounting
position markings.
4.
Mount the tank cover and lock it.
► Fig.11: 1. Tank cover 2. Powder filter (HEPA)
3. Damper 4. Prefilter 5. Tank 6. Mounting
position marking
NOTICE:
Before using the powder filter, make
sure that prefilter and damper are used together. It
is not allowed to install powder filter alone.
Installing the water filter
Optional accessory
NOTICE:
Never pick up water or wet dust without
the float and the cloth filter or the water filter.
NOTICE:
For picking up wet dust, make sure that
the float cage and the float are installed on the
cleaner.
NOTICE:
When installing the water filter on the
tank, set it tight at the opening of the tank so
that the hook of the water filter engages the tank
opening firmly and there is no space between the
water filter and the tank.
To pick up water or wet dust only, the water filter is more
suitable than the cloth filter.
When installing the water filter, align its mounting posi-
tion marking with the one on the tank.
► Fig.12: 1. Water filter 2. Tank 3. Mounting position
marking
NOTE: It is recommended using water filter when
picking up large amount of water repeatedly.
Otherwise vacuum ability may be reduced in case of
cloth filter.
Installing the paper pack
Optional accessory
WARNING:
make sure that the cloth filter or prefilter is used
together. Failure to use the cloth filter / prefilter
together may cause unusual noise and heat, resulting
in a fire.
NOTICE:
Never pick up water or other liquids or
wet dusts when using the paper pack. Picking up
such things may cause the paper pack breakage.
NOTICE:
When using the cloth filter, make sure
that the float and the float cage are attached on
the tank cover.
NOTICE:
When using the prefilter, make sure
that the powder filter and the damper are used
together.
1. Remove the rubber holder.
► Fig.13: 1. Rubber holder
2. Extend the paper pack.
3. Align the paper pack opening with the dust suction
opening of the cleaner.
4.
Insert the cardboard part of the paper pack onto
the holder so that it is positioned at the end beyond the
detent protrusion.
► Fig.14: 1. Paper pack 2. Holder
11 ENGLISH
Before using the paper pack,