Using The Saw - EINHELL TKS 1500 ECO Mode D'emploi D'origine

Anleitung_TKS_1500_Eco_SPK1__ 15.10.13 09:10 Seite 23
6. Assembly
Important! Pull out the power plug before
carrying out any maintenance, resetting or
assembly work on the cutting-off machine!
6.1 Assembling the base frame (Fig. 15/16/17)
Turn the saw upside down and place it on the
n
floor.
Use the washers (b) and the hex screws (a) to
n
fasten the 4 legs (29) loosely to the saw.
Now use the hex screws (a), the washers (b)
n
and the nuts (c) to fasten the longitudinal struts
(31) and the cross-struts (30) loosely to the legs.
Please note: The longer struts have to be used
on the sides.
Finally, tighten all screws and nuts on the base
n
frame.
Screw the additional legs (A) to the rear legs
n
(29) so that they point towards the rear of the
machine (Fig. 23).
6.2 Fitting / removing the saw blade guard (Fig. 3)
Mount the saw blade guard (2) on the splitter (5)
n
so that the screw fits through the hole (18) in the
splitter.
Do not tighten the screw (15) too far – the blade
n
guard must be able to move freely.
Fasten the extractor hose (13) to the extractor
n
adapter (16) and to the extractor socket of the
blade guard (2).
A suitable extractor system has to be connected
n
to the outlet of the extractor adapter (16).
To remove the saw blade guard, proceed in
n
reverse order.
Important!
The guard hood (2) must always be lowered
over the workpiece before you begin to cut.
6.3. Setting the splitter (Fig. 3/5/6/7)
Important! Pull out the power plug.
n
Set the blade (4) to max. cutting depth, move to
n
0° position and lock in place.
Remove the saw blade guard (see 6.2).
n
Take out the table insert (6) (see 6.4).
n
Slacken the fixing screw (19).
n
6.3.1. Setting for maximum cuts (Fig. 5/6/7)
Push up the splitter (5) until the gap between the
n
saw table (1) and the upper edge of the splitter
n
(5) equals approx. 10 cm.
The distance between the blade (4) and the
n
splitter (5) should be 3-5 mm.
Retighten the screw (19) and mount the table
n
insert (6) (Fig. 6).
6.4 Changing the table insert (Figure 6)
To prevent increased likelihood of injury the
n
table insert should be changed whenever it is
worn or damaged.
Remove the saw blade guard (2).
n
Remove the 1 countersunk head screws (17).
n
Take out the worn table insert (6).
n
To fit the replacement table insert, proceed in
n
reverse order.
6.5 Fitting/replacing the blade (Fig. 4)
Important! Pull out the power plug first.
n
Remove the table insert by undoing the two
n
countersunk head screws (see 6.4).
Undo the nut with a size 24 wrench on the nut
n
itself and a second fork wrench (size 13) on the
motor shaft to apply counter-pressure.
Important! Turn the nut in the direction of
n
rotation of the saw blade.
Take off the outer flange and pull the old saw
n
blade off the inner flange by dropping the blade
at an angle.
Clean the blade flange thoroughly before fitting
n
the new blade.
Mount and fasten the new saw blade in reverse
n
order.
Important! Note the running direction. The
n
cutting angle of the teeth must point in
running direction, i.e. forwards (see the
arrow on the blade guard).
Refit and set the splitter (5) and the saw guard
n
(2) (see 6.2., 6.3.)
Check to make sure that all safety devices are
n
properly mounted and in good working condition
before you begin working with the saw again.

7. Using the saw

7.1. ON/OFF switch (Fig. 1)
To turn the saw on, press the green button "I" .
n
Wait for the blade to reach its maximum speed
of rotation before commencing with the cut.
To turn the machine off again, press the red
n
button "0".
7.2. Cutting depth (Fig. 1)
Turn the hand crank (8) to set the blade (4) to
n
the required cutting depth.
Turn anti-clockwise: larger cutting depth
Turn clockwise: smaller cutting depth
GB
23