Using The Saw - EINHELL TH-TS 1525 eco Mode D'emploi D'origine

6.3.1. Setting for maximum cuts (Fig. 5/6/7)
•
Push up the splitter (5) until the gap between
the saw table (1) and the upper edge of the
splitter (5) equals approx. 10 cm.
•
The distance between the blade (4) and the
splitter (5) should be 3-5 mm.
•
Retighten the screw (19) and mount the table
insert (6) (Fig. 6).
6.4 Changing the table insert (Figure 6)
•
To prevent increased likelihood of injury the
table insert should be changed whenever it is
worn or damaged.
•
Remove the saw blade guard (2).
•
Remove the 1 countersunk head screws (17).
•
Take out the worn table insert (6).
•
To fit the replacement table insert, proceed in
reverse order.
6.5 Fitting/replacing the blade (Fig. 4)
•
Important! Pull out the power plug first.
•
Remove the table insert by undoing the two
countersunk head screws (see 6.4).
•
Undo the nut with a size 24 wrench on the
nut itself and a second fork wrench (size 10)
on the motor shaft to apply counter-pressure.
•
Important! Turn the nut in the direction of
rotation of the saw blade.
•
Take off the outer flange and pull the old saw
blade off the inner flange by dropping the bla-
de at an angle.
•
Clean the blade flange thoroughly before fit-
ting the new blade.
•
Mount and fasten the new saw blade in rever-
se order.
•
Important! Note the running direction. The
cutting angle of the teeth must point in run-
ning direction, i.e. forwards (see the arrow on
the blade guard).
•
Refit and set the splitter (5) and the saw gu-
ard (2) (see 6.2., 6.3.)
•
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
Anl_TH_TS_1525_eco_SPK1.indb 26 Anl_TH_TS_1525_eco_SPK1.indb 26
GB

7. Using the saw

7.1. ON/OFF switch (Fig. 1)
•
To turn the saw on, press the green button
"I". Wait for the blade to reach its maximum
speed of rotation before commencing with the
cut.
•
To turn the machine off again, press the red
button "0".
7.2. Cutting depth (Fig. 1)
Turn the hand crank (8) to set the blade (4) to the
required cutting depth.
Turn anti-clockwise:
larger cutting depth
Turn clockwise:
smaller cutting depth
7.3. Parallel stop
7.3.1. Stop height (Fig. 9-13)
•
The parallel stop (7) supplied with the bench-
type circular saw has two different guide
faces.
•
For thick material you must use the stop rail
(23) as shown in Fig. 11, for thin material you
must use the stop rail as shown in Fig.10.
•
To change over the stop rail (23) to the lo-
wer guide face you have to slacken the two
knurled screws (26) in order to disconnect the
stop rail (23) from the holder (24).
•
Remove the two knurled screws (26) through
the one slot (27) in the stop rail (23) and in-
sert in the other slot (25).
•
Remount the stop rail (23) on the holder (24).
•
The procedure for changing over to the high
guide face is similar.
7.3.2. Cutting width:
•
The parallel stop (7) has to be used when
making longitudinal cuts in wooden workpie-
ces.
•
The parallel stop (7) can be mounted on eit-
her side of the saw table (1).
•
The parallel stop (7) has to be mounted in the
guide rail (28) of the saw table (1).
•
The parallel stop (7) can be set to the requi-
red dimension with the help of the scale (22)
on the guide rail (1).
- 26 -
29.04.14 13:03 29.04.14 13:03