JB Systems DYNASPOT Mode D'emploi page 12

ENGLISH
OPERATE THE UNIT BY INFRARED REMOTE
When used in standalone or master/slave mode we strongly advise you to use the included infrared remote
control. For proper operation make sure to point the remote to the front panel of the master unit. Now you
can control all the connected units:
1. [BLACKOUT] button: used to switch the output ON/OFF.
2. [FULL STROBE] button: press to select fast strobe in
white color and full output, no gobo selected. Press again
to return to normal.
3. [FULL WHITE] button: press to select white color at full
output and no gobo selected. Press again to return to
normal.
4. [SOUND] button:
movements to the beats of the music.
5. [AUTO] button: Press to trigger the PAN/TILT movements
automatically. You can adjust the speed by pressing the
[+/–] buttons (6).
6. + / - buttons: used to increase / decrease the value of
certain functions.
7. [DIM] button: press the [DIM] button followed by one of
the 9 number buttons (13) to select one of the preset
dimmer levels (10% steps) or press the [DIM] button
followed by the [+/-] buttons (6) to set the output exactly as
you want.
8. [TILT / PAN] buttons: press the [TILT] or [PAN] button,
followed by the [+/-] buttons to point the beams in a certain
direction. Just press the [SOUND] or [AUTO] buttons to
return back to normal pan/tilt movements.
9. [COLOR] button: press the [COLOR] button followed by one of the 9 number buttons (13) to select one
of the colors. Number button "9" will scroll the different colors automatically at medium speed.
10. [GOBO] button: press the [GOBO] button followed by one of the 9 number buttons (13) to select one of
the gobos. Number buttons "8" & "9" will scroll the different gobo automatically at slow or medium speed.
11. [STROB] button: press the [STROB] button followed by one of the 9 number buttons (13) to select the
desired strobe function: "1"= no strobe, "2" = random strobe, "3" to "9" = strobe with increasing speed.
12. [SPEED] button: press the [SPEED] button followed by one of the 9 number buttons (13) to select the
desired PAN/TILT speed: "1"= complete stop, "2" to "9" = pan/tilt movements with increasing speed.
13. [1...9] number buttons: used to select preset values for the different functions.
14. [RESET] button: this button allows you to reset the projectors from a distance. When you press this
button shortly nothing happens, when you press this button for more than 3 seconds the units start
resetting. (only to be used when something is wrong and a reset seems needed)
MAINTENANCE
 Make sure the area below the installation place is free from unwanted persons during servicing.
 Switch off the unit, unplug the mains cable and wait until the unit is cooled down.
During inspection the following points should be checked:
 All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
 Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
 When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
 The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
 In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.
 The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
 The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit's optics.
 Clean with a soft cloth using normal glass cleaning products.
JB SYSTEMS
®
Press to trigger the PAN/TILT
10/59
USER MANUAL
DYNASPOT