Dimensions - turck TX-IO-XX03 Guide Rapide

TX-IO-XX03
Voltage outputs
Description Specifications
Type Single-ended
Voltage range ±10 VDC
Load impedance min. 1 kΩ
Load capacitance max. 10 nF
Linearity error 0.15 %
Current outputs
Description Specifications
Type Current source
Current range 0...20 mA or 4...20 mA
Load impedance max. 470 Ω
Linearity error 0.2 %
Environmental Conditions
Description Specifications
Operating 0...50 °C
temperature
Storage temperature -20...70 °C
Operating humidity 5...85 % relative humidity, non condensing
Connection technology
Description Specifications
Connector type 8 male connectors 10 pol., 3,5 mm grid/
Weidmueller - Omnimate BLZF 3.5/180F)

Dimensions

See fig. 1
Mounting
Remove the connector protective cover from the equipment before installing
the module and mount the module according to fig. 2.
Unmounting
ATTENTION
Risk of short circuits
Destruction of electronic circuits!
Do not connect or disconnect when energized.
➤
Pin assignment/connector view
See fig. 3
Pin CN1 (AI) CN2 (AI)
1 Pt100_1 supp. Pt100_3 supp.
2 CH_1 + input CH_3 + input
3 CH_1 - input CH_3 - input
4 COM-AGND COM-AGND
5 SHIELD (case) SHIELD (case)
6 Pt100_2 supp. Pt100_4 supp.
7 CH_2 + input CH_4 + input
8 CH_2 - input CH_4 - input
9 COM-AGND COM-AGND
10 SHIELD (case) SHIELD (case)
Pin CN5 (DI) CN6 (DI)
1 + 24 VDC + 24 VDC
2 DI1 DI9
3 DI2 DI10
4 DI3 DI11
5 DI4 DI12
6 DI5 DI13
7 DI6 DI14
8 DI7 DI15
9 DI8 DI16
10 GND GND
CN3 (AO) CN4 (mixed)
CH1 Pt100_5 supp.
COM-AGND CH_5 + input
CH2 CH_5 - input
COM-AGND COM-AGND
SHIELD (case) SHIELD (case)
CH3 n.c..
COM-AGND + 24 VDC in
CH4 + 24 VDC in
COM-AGND GND in
SHIELD (case) GND in
CN7 (mixed) CN8 (DO)
+ 24 VDC + 24 VDC
DI17 DO5
DI18 DO6
DI19 DO7
DI20 DO8
DO1 DO9
DO2 DO10
DO3 DO11
DO4 DO12
GND GND
Wiring Examples
Standard digital inputs and outputs
NOTE
The cables must not be longer than 30 m.
See fig. 4
Example: Two digital inputs (switches) and two digital outputs connection.
NOTE
Pin 1 of CN5, CN6, CN7 and CN8 is locally connected to the I/O supply (CN4, Pin
7 and 8, 24 VDC in) and can be used in order to simplify external connecting
of sensors (for example, external switches could be supplied from these pins,
instead from main supply).
NOTE
Pin 10 of CN5, CN6, CN7 and CN8 is locally connected to to the I/O supply (CN4,
Pin 9 and 10, GND in) and can be used in order to simplify external connecting
of actuators (external loads can be conntect to GND using these pins, instead of
using the main supply).
Encoder connection
See fig. 5
Example: Logic connection of two encoder modules. The encoder modules must
be 24 VDC powered (connect GND-potential reference of the encoder to the
GND-potential of TX-IO-XX03 digital I/O supply).
Counter or frequency inputs
See fig. 6
Example: Logic connection for two counter/frequency measurement.
Connection is suitable for counter inputs (pulse and gate) and/or frequency
inputs (frequency and gate).
The external modules must be 24 VDC powered (connect the GND-potential of
the external module to the GND-potential of TX-IO-XX03 digital I/O supply).
Voltage inputs, single ended, differential or current inputs
See fig. 7
Example:
Logic connection for various configurations:
■
Two single ended analog inputs on the same channel (for example used
CH_2+ , CH_2- and COM-AGND).
■
One differential voltage source, connected as differential channel at CH_4+
CH_4- pair.
■
One current input connected to CH_3+ CH_3- pair
Pt100,thermocouple, and analog outputs
See fig. 8
Example: Logic connection for various configurations:
■
One Pt100 (three wire) connected to CH2.
■
One Pt100 (four wire) connected to CH4.
■
One thermocouple, connected to CH3.
■
One Pt100 connected to CH5 and used for thermocouple input compensa-
tion.
■
One analog output (CH4)
Approvals and standards
The product has been designed for use in combination with the HMIs of the
TX500 product family in an industrial environment in compliance with the
2014/30/EU directive.
Compliance
The products have been designed in compliance with:
■
EN 61000-6-4/ EN 61000-6-2
■
EN 61000-4-2 to -4-6, EN 61000-4-8
■
EN 55011, Class A
■
EN 60945
ATTENTION
Operation in residential and commercial areas
Electromagnetic disturbances!
In case of the operation of the devices in residential and commercial areas,
➤
observe the measurement values according to IEC-61000-6-3.
© Hans Turck GmbH & Co. KG | D301403 2016-06 DE EN FR