Accessories - Worx WG324E Notice Originale

If the tool is to be used regularly then invest in anti
vibration and noise accessories.
Plan your work schedule to spread any high vibration tool
use across a number of days.

ACCESSORIES

Chain (WA0142)
Guide bar (WA0151)
Lubrication oil
Bar and Chain
Sheath/Scabbard
Charger (WA3880)
Battery (WA3551)
Extension pole
(WA4301)
We recommend that you purchase your accessories
from the same store that sold you the tool. Refer to the
accessory packaging for further details. Store personnel
can assist you and offer advice.
INTENDED USE
• The mini pruning saw is intended for cutting only wood
and branches up to a diameter corresponding to the
16
length of the pruning saw guide bar.
• The mini pruning saw must be used at ground level or
from a suitable platform that is completely stable and
secure.
• During using, the mini pruning saw should be held in
both hands, right hand on the Grip Area and left hand on
the Secondary Grip Area.
• The mini pruning saw is intended for outdoor use only.
• The mini pruning saw is not intended for any other use.
• Mounting of parts on the mini pruning saw is
authorized only for original or manufacturer-approved
spare parts (chain guides or saw chains for example)
as well as for authorized chain guide / saw chain
combinations as indicated in the manual.
• The user is responsible for any accident resulting from
improper use or unauthorized modification of the mini
pruning saw.
ASSEMBLY
WARNING! Do not install the battery pack before
it has been completely assembled.
Always use gloves when handling the chain.
MOUNTING THE SAW CHAIN
1. Unpack all parts carefully. Remove the Housing-
Cover by turning the Housing-Cover Knob in a
counterclockwise direction. (See Fig. A1)
2. Place the pruning saw on a solid, level surface.
3. Use only genuine Worx Chains or those
recommended for Guide Bar.
Cordless Pruning Saw
WG324E WG324E.1 WG324E.9
1 1
1 1
1 1
1 1
1 1
1 1
/ 1
4. Slide the Chain in the slot around the Guide Bar.
Ensure the Chain is in correct running direction by
comparing it to the chain icon on the Guide Bar, or
referring to the chain direction symbol found on the
saw body. (See Fig. A2)
5. Fit the Chain onto the Drive Sprocket, so that the
Fastening Bar Bolt and the Bar Locating Tab on the
Bar Pad fit into the keyway of the opening on the
Guide Bar. (See Fig. B1, B2)
6. Assure all parts are seated properly. Make sure the
1
drive links are fully seated in the Drive Sprocket (See
Fig. C1), avoiding a kink as shown in Fig. C2. If kink
1
occurs, pick up the Chain at the Guide Bar just ahead
of the kink and then pull the kink out.
1
NOTE: Chain should rotate freely and be free of kinks.
7. Fit the Chain Cover and tighten the Chain Cover by
1
turning the Housing-Cover Knob clockwise until it is
tight. (See Fig. D)
/
WARNING: The Chain is not yet tensioned.
/
Tensioning the Chain applies as described under
"TENSIONING CHAIN". The Chain now needs to be
/
inspected to make sure it is properly tensioned.
TENSIONING CHAIN (See Fig. E1, E2, E3)
NOTE: New saw chains will stretch. Check the chain
tension frequently when first used and tighten when the
Chain becomes loose around the Guide Bar.
WARNING:
• Removing the battery pack before adjusting
saw chain tension.
• Cutting edges on chain are sharp. Use protective
gloves when handling chain.
• Maintain proper chain tension always. A loose
chain will increase the risk of kickback. A loose
chain may jump out of guide bar groove. This may
injure operator and damage chain. A loose chain
will cause chain, bar, and sprocket to wear rapidly.
1. Place the pruning saw on any suitable flat surface.
2. Loosen the Housing-Cover Knob a bit to loosen the
Chain Cover lightly.
3. Adjust the chain tension. Turn the Chain Tensioning
Screw clockwise to tighten. (See Fig. E1)
4. The correct chain tension is reached when the Chain
can be raised approx. half the drivelink depth from
the Guide Bar in the center. (See Fig. E2)
5. Tighten the Housing-Cover Knob to secure the Chain
Cover. (See Fig. E3)
NOTE: The Chain is properly tensioned when it can
be lifted off of the Guide Bar and the drivelink is
within the rail of the Guide Bar.
NOTE: The chain will naturally stretch and lose
proper tension under general use. To re-tention,
repeat steps 1-5 listed above.
ASSEMBLING THE EXTENSION POLE (Only for
WG324E.1)
Align and insert the handle of extension pole into the
shaft. Rotate the Locking Knob clockwise to lock. (See
Fig. F1, F2)
NOTE: Make sure that the shaft is firmly locked in place.
EN