IMG STAGELINE LE-504 Mode D'emploi page 11

1 2 3 4 5 6 7 8 9 10
D I P ON
DMX start address 104 = 64 + 32 + 8
The easiest way is always to start from the highest
possible switch value and to add the smaller
values.
After adjusting the start address for the 1st channel,
the channels 2 to 4 are assigned to the following
addresses. Example:
Start address 104 = colour, fade mode,
address 105 = chaser functions
address 106 = speed for fade mode and
address 107 = dimmer
7 Cleaning of the Colour Filter Panes
The colour filter panes should be cleaned at regular
intervals, depending on impurities caused by dust,
smoke, or other particles. Only in this case the light
can be radiated at maximum brightness.
9 Configuration of the DMX Channels
Channel 1
colours, fade mode, chaser mode
240 – 255 chaser mode
(automatic colour change)
chaser function can be adjusted with channel 2
chaser speed can be adjusted with channel 3
224 – 239 fade mode
(automatic fading in and fading out of the
light of the individual lamps in succession)
fading speed of the light can be adjusted with channel 3
105 – 111 colour 16 217–223 colour 32
098 – 104 colour 15 210–216 colour 31
091 – 097 colour 14 203–209 colour 30
084 – 090 colour 13 196–202 colour 29
077 – 083 colour 12 189–195 colour 28
070 – 076 colour 11 182–188 colour 27
063 – 069 colour 10 175–181 colour 26
056 – 062 colour 9 168–174 colour 25
049 – 055 colour 8 161–167 colour 24
042 – 048 colour 7 154–160 colour 23
035 – 041 colour 6 147–153 colour 22
028 – 034 colour 5 140–146 colour 21
021 – 027 colour 4 133–139 colour 20
014 – 020 colour 3 126–132 colour 19
007 – 013 colour 2 119–125 colour 18
000 – 006 colour 1 112–118 colour 17
All rights reserved by MONACOR
be reproduced in any form or by any means for any commercial use.
chaser mode
chaser mode
preprogrammed change of colour
change of colour at random
change pink /blue/green/ red
change red /yellow/orange/ cyan
change red/green/ yellow/blue
® INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may
WARNING
Prior to opening the unit, always discon-
nect the plug from the mains socket and
let the unit cool down at least 5 minutes!
For cleaning use a soft, clean cloth and a commercial
detergent for glass. Take care that no liquid penetrates
the inside of the unit. Then carefully wipe the panes
dry.
8 Specifications
Power supply: . . . . . . . . . 230 V~/50 Hz
Power consumption: . . . . 2100 VA
Lamp: . . . . . . . . . . . . . . . 4 x halogen tube lamp,
Ambient temperature: . . . 0 – 40 °C
Dimensions, weight: . . . . 450 x 275 x 175 mm, 7 kg
Subject to technical modification.
Channel 2
chaser functions
232–255
change yellow/ green
211– 231
change red/green
190 – 210
change yellow/blue
169–189
change blue/ red
148–168
change green/ pink
127–147
change red /cyan
106–126
change orange/pink
085–105
064–084
043–063
023–042
000–022
230 V/500 W, base R7s
(not supplied with the unit)
Channel 3
speed for fade mode and
chaser mode
255
fast
000
slow
GB
Channel 4
dimmer
255
dark
000
bright
11