Fusion Apollo RA770 Mode D'emploi page 4

Wire or RCA Bare Wire Notes
Connector Function Color or
RCA Label
Name
Zone 2 line out (left) ZONE 2 Provides output to an external amplifier, and is
associated with the volume control for zone 2.
Zone 2 line out (right) ZONE 2 SUB
OUT Each subwoofer cable provides a single mono
Zone 2 subwoofer out
output to a powered subwoofer or subwoofer
amplifier.
Auxiliary in 1 left AUX IN 1 Provides an RCA stereo line input for audio
sources, such as a CD or MP3 player.
Auxiliary in 1 right
Zone 3 line out (left ) ZONE 3 Provides output to an external amplifier, and is
associated with the volume control for zone 3.
Zone 3 line out (right) ZONE 3 SUB
OUT Each subwoofer cable provides a single mono
Zone 3 subwoofer out
output to a powered subwoofer or subwoofer
amplifier.
Zone 4 line out (left) ZONE 4 Provides output to an external amplifier, and is
associated with the volume control for zone 4.
Zone 4 line out (right) ZONE 4 SUB
OUT Each subwoofer cable provides a single mono
Zone 4 subwoofer out
output to a powered subwoofer or subwoofer
amplifier.
Auxiliary in 2 left AUX IN 2 Provides and RCA stereo line input for audio
sources, such as a CD or MP3 player.
Auxiliary in 2 right
Connecting to Power
When connecting the stereo to power, you must connect both power wires.
You should connect the yellow power wire directly to the battery. This provides
power to the stereo and a constant trickle-power standby feed.
You should connect the red signal wire to the same battery through the ignition
or another manual switch to turn the stereo on and off. If you are not routing
the red wire through the ignition or another manual switch, you can connect
the red wire to the yellow wire, and connect them both to the positive (+)
battery terminal.
You must connect the power wire to the battery through a 15 A fuse or a 15 A
circuit breaker.
If it is necessary to extend the yellow power and black ground wires, use
2
14 AWG (2.08 mm ) wire. For extensions longer than 1 m (3 ft.), use 12 AWG
(3.31 mm²) wire. If it is necessary to extend the red wire, use 22 AWG
2
(0.33 mm ) wire.
1
Route the yellow power , red signal
battery, and route the wiring-harness plug to the stereo.
Do not connect the wiring harness to the stereo until all of the bare wire
connections have been made.
2 Connect the black wire to the negative (-) battery terminal.
3 Complete an action:
• If you are routing the red wire through the ignition or another manual
switch , connect the red signal wire to the ignition or switch, install a
15 A fuse on the yellow wire as close to the battery as possible, and
connect the yellow wire to the positive (+) battery terminal.
• If you are not routing the red wire through the ignition or switch,
connect the red wire to the yellow wire, install a 15 A fuse as close to
the battery as possible, and connect both wires to the positive (+)
battery terminal.
Speaker Zones
You can group speakers in one area into a speaker zone. This enables you to
control the audio level of the zones individually. For example, you could make
the audio quieter in the cabin and louder on deck.
4
Up to two pairs of speakers can be connected per channel of each zone, in
parallel. A zone can support no more than four speakers using the on-board
amplifier.
Zones 1 and 2 are powered by the on-board amplifier. To use the RCA line
outputs and the RCA subwoofer outputs for zones 1 and 2, you must connect
external amplifiers.
Zones 3 and 4 are available as line-level outputs only. To use the RCA line
outputs and the RCA subwoofer outputs for zones 3 and 4, you must connect
external amplifiers.
You can set the balance, volume limit, tone, subwoofer level, subwoofer
frequency, and name for each zone, and configure other zone-specific
settings.
Single-Zone System Wiring Example
Extended System Wiring
This diagram illustrates a system installation with an external amplifier and
subwoofer connected to zone 2 on the stereo. You can connect an amplifier
and subwoofer to any or all of the four zones on the stereo.
, and black ground wires to the
Speakers
Water-tight connection
Item Description
Zone 1 speakers
Water-tight connection
Zone 2 speakers
Amplifier-on signal wire
You must connect this wire to each amplifier connected to a zone line out.
Powered amplifier connected to the zone 2 line out
Zone 2 line out and subwoofer out
Each subwoofer cable provides a single mono output to a powered subwoofer or
subwoofer amplifier.
Subwoofer
Installation Instructions