Accessories - Metabo TE 24-230 MVT CED Notice Originale

en ENGLISH
Continuous operation (depending on features)
Switching on: Slide the lock (23) in the direction of
the arrow, press the trigger switch (24) and
keep it pressed. The machine is now
switched on. Now slide the lock (23) in the
direction of the arrow once more to lock the
trigger switch (24) (continuous operation).
Switching off: Press the trigger switch (24) and
release.
8.2 Working
Always hold and guide the tool by the main
handle (13) of the angle grinder and side
handle (6), using both hands.
Push / pull the machine only in the direction
of the arrow (7)
1. Set required cutting depth:
Loosen the clamping nut (3) and set the required
cutting depth at the scale, tighten clamping nut
(3) again.
2. Position the guard with the front part of the guide
table (10) onto the workpiece without the
diamond cutting disc touching the workpiece.
3. Switch on machine and wait until the full speed
has been reached.
4. For plunge cuts: Slowly and carefully swivel the
machine downwards. The diamond cutting discs
plunges into the workpiece.
5. Slowly guide the machine in the direction of the
arrow (7): The diamond cutting disc cuts into the
workpiece.
6. Pull/push machine only in direction of the
arrow (7) (work in reverse rotation). Otherwise
there is the danger of the machine kicking back
from the cut out of control. Guide the machine
evenly at a speed suitable for the material being
processed. For optimal extraction ensure that
the wheels always touch the workpiece. The
guide table (10) must glide on the workpiece.
7. Once the cut is complete, switch off the tool and
hold it steady until the diamond cutting disc
comes to a stop. Never attempt to remove the
cutting disc from the cut while the wheel is
in motion otherwise kickback may occur.
8. Put machine aside.
9. Maintenance
Prior to each use, check if there are parts
missing, worn, broken, torn or damaged. Do not
use a defective or incomplete guard.
Significantly reduced work progress and increased
feed force are signs for blunt diamond cut-off
wheels. Sharpen blunt diamond cut-off wheels by
carrying out short cuts into abrasive materials such
as sand-lime brick.
10. Cleaning
Cleaning the motor: It is possible
that particles deposit inside the
power tool during operation. This impairs the
cooling of the power tool. Conductive build-up can
impair the protective insulation of the power tool and
create an electrical hazard.
16
The power tool should be cleaned regularly, often
and thoroughly through all front and rear air vents
using a vacuum cleaner or by blowing in dry air.
Prior to this operation, separate the power tool from
the power source and wear protective glasses and
dust mask. Ensure appropriate suction is available
when blowing out vents.
Button (22) for adjusting the handle:
Occasionally blow compressed air through the
button (when pressed, in all 3 main handle
positions). Prior to this operation, separate the
power tool from the power source and wear
protective glasses and dust mask.
11. Troubleshooting
- Overload protection: The electronic signal
display (12) lights up and the load speed
decreases dramatically. The motor temperature
is too high! Run the machine in idling until it cools
down and the electronic signal display switches
off.
- Overload protection: The electronic signal
display (12) lights up and the load speed
decreases slightly. The machine is overloaded.
Work with a reduced load until the electronic
signal display goes out.
- Electronic safety stop: The electronic signal
display (12) lights up and the machine was
SWITCHED OFF automatically. If the slew rate
of the current is too high (for example, if the
machine suddenly seizes or kickback occurs), the
machine switches off. Switch off the machine at
the trigger switch (24). Switch it on again and
continue to work as normal. Try to prevent the
machine from seizing. See chapter 4.2.
- Restart protection: The electronic signal
display (12) FLASHES and the machine does
not start. Restart protection is active. If the mains
plug is inserted with the machine switched on or if
the power supply is restored following an
interruption, the machine does not start up. Switch
the machine off and back on again.
- When switched on, the machine accelerates
to maximum speed very quickly, i.e. automatic
restriction of the starting current does not work
(soft start). An electronic error exists. Other
safety-related electronic functions are no longer
available. Have the machine repaired immediately
(see 13.).

12. Accessories

Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
The maximum permitted thickness of the
diamond cutting disc is 3 mm (1/8"). Do not
use any segmented diamond cutting discs with
segment slits >10 mm. If using segmented diamond
cutting discs, only a negative segment cutting angle
is permitted.
See www.metabo.com or the catalogue for a
complete range of accessories.