Maintenance; Tips And Tricks; Available Accessories; Repairs - Metabo PK 200 Instructions D'utilisation Originales

ENGLISH
9.7

Maintenance

Before switching on
Visual check if distance saw blade – riv-
ing knife is 3...5 mm.
Visual check of power cable and power
cable plug for damage; if necessary
have damaged parts replaced by a qual-
ified electrician.
Monthly (if used daily)
remove saw dust and chips with vacuum
or brush; apply light coat of oil to guide
elements:
− threaded rod and guide rods of
blade rise and fall mechanism:
− swivel segments.
Every 300 hours of operation
Check all screwed joints, retighten if
necessary.

10. Tips and Tricks

•
Before cutting a workpiece to size
make trial cuts with pieces of scrap.
•
Always place a workpiece on the
saw table in such way that it can not
tilt or rock (e.g. always place a
curved board on the table with the
convex side up).
•
When working long stock use suita-
ble supports, such as table rear or
side extensions (optional accesso-
ries).
•
To simplify repetitive cut-off work
use a stock stop (optional acces-
sory).
•
Keep surfaces of saw table and saw
base clean – in particular, remove
resin residue with a suitable clean-
ing and maintenance spray (optional
accessory).

11. Available Accessories

For special tasks the following accesso-
ries are available at your specialized
dealer – see back cover for illustrations:
A Workstand
Provides for a secure machine
stand and optimal working height;
ideal in mobile use, folds up for sav-
ing space.
B Base System Rail
Required for the installation of Slid-
ing Carriage, Table Side or Table
Rear Extension.
C Base System Rail Extension
To extend the Base System Rail to
20
1350 mm. The enclosed support
leg provides for a firm stand.
D Support leg for Base System Rail
Extension
Provides extra support for the Base
System Rail Extension.
E Sliding Carriage with Mitre Fence
For installation on the Base System
Rail. Capacity before the blade up
to 600 mm.
F Table Side Extension
For installation on the Base System
Rail. Extends the saw table to the
left or right.
G Rear Table Extension with support
leg
For installation on the Base System
Rail. Extends the saw table at front
and/or rear by 1000 mm.
H Dust Collection Attachment
Helps to protect your health and to
keep the shop clean.
I Suction Adapter
To connect a shop vacuum to the
dust collection attachment.
J Roller/Ball Transfer Stand
For accurate guiding of long stock.
K Care and Maintenance Spray
To remove resin residue and pre-
serve metal surfaces.
L TCT Saw Blade
210x2.4/1.6x30 30 ATB
For rip and cross cuts in grown tim-
ber and particle board.
M TCT Saw Blade
210x2.4/1.6x30 42 ATB
For rip and cross cuts in panels;
plastic, aluminium, copper extru-
sions and high-grade veneered
sheets.
N TCT Saw Blade
210x2.4/1.6x30 64 ATB
General purpose blade for plastics
and metals.

12. Repairs

A
Danger!
Repairs to electric tools must
be carried out by qualified electri-
cians only!
Electric tools in need of repair can be
sent to the service centre of your coun-
try. Refer to the spare parts list for the
address.
Please attach a description of the fault to
the electric tool.

13. Environmetal Protection

The saw's packaging can be 100% recy-
cled.
Worn out electric tools and accessories
contain considerable amounts of valua-
ble raw and plastic materials, which can
be recycled.
These instructions are printed on chlo-
rine-free bleached paper.

14. Trouble Shooting

A
Danger!
Before carrying out any fault
service or maintenance work always:
1. switch machine OFF;
2. unplug power cable;
3. wait for saw blade to come to
standstill.
Check to see that all safety devices
are operational after each fault serv-
ice.
Motor does not run
Undervoltage relay tripped by power fail-
ure:
− switch on again.
No mains voltage:
− check cables, plug, outlet and mains
fuse.
Motor overheated, e.g. by a blunt saw
blade or chip build-up in the chip case:
− eliminate cause for overheating,
wait for a few minutes, then start
saw again.
Stated top speed is not reached
Motor supply voltage too low:
− use a shorter extension cable or
extension cable with larger lead
cross section
2
(≥ 1.5 mm ).
− Have power supply checked by a
qualified electrician.
Loss of cutting performance
Saw blade blunt (possibly tempering
marks on blade body):
− replace saw blade (see section
"Maintenance").
Chip ejection tube blocked
No dust collector hooked up or suction
capacity insufficient:
− connect dust collector or
− increase suction capacity (air speed
≥ 20 m/sec at chip ejection tube).