Initial Operation - Metabo TE 24-230 MVT CED Notice Originale

en ENGLISH
The workpiece must lay flat and be secured against
slipping, e.g. using clamps. Large workpieces must
be sufficiently supported.
Damaged, eccentric or vibrating tools must not be
used.
Ensure that the spot where you wish to work is free
of power cables, gas lines or water pipes (e.g.
using a metal detector).
Avoid damage to gas or water pipes, electrical
cables and load-bearing walls (static).
Pull the plug out of the socket before making any
adjustments, converting or servicing the machine.
A damaged or cracked additional handle must be
replaced. Never operate a machine with a defective
additional handle.
Prior to each use, check if there are parts missing,
worn, broken, torn or damaged. Do not use a
defective or incomplete guard.
Use only the supplied clamping devices.
Reducing dust exposure:
WARNING - Some dust created by power
sanding, sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
- Lead from lead-based paints,
- Crystalline silica from bricks and cement and
other masonry products, and
- Arsenic and chromium from chemically treated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well-
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
This also applies to dust from other materials such
as some timber types (like oak or beech dust),
metals, asbestos. Other known diseases are e.g.
allergic reactions, respiratory diseases. Do not let
dust enter the body.
Observe the relevant guidelines and national
regulations for your material, staff, application and
place of application (e.g. occupational health and
safety regulations, disposal).
Collect the particles generated at the source, avoid
deposits in the surrounding area.
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- do not direct the escaping particles and the
exhaust air stream towards yourself or nearby
persons or towards dust deposits,
- use an extraction unit and/or air purifiers,
- ensure good ventilation of the workplace and keep
it clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
- Vacuum or wash protective clothing. Do not blow,
beat or brush protective gear.
14
5. Overview
See pages 2 and 3.
1 Extractor connection piece
2 Thread for side handle (on both sides)
3 Clamping nut (cutting depth limitation)
4 Scale (depth of cut)
5 Allen screwdriver
6 Side handle (of the angle grinder) *
7 Push machine only in direction of arrow
8 Extraction guard
9 Arrow indicating direction of rotation (direction
of rotation of the diamond cutting disc)
10 Guide table
11 Spindle locking button (of the angle grinder) *
12 Electronic signal display (of the angle grinder) *
13 Main handle of the angle grinder *
14 Spindle (of the angle grinder) *
15 Support flange (of the angle grinder) *
16 two spacer discs
17 Diamond cutting disc *
18 2-hole adjusting nut
19 two-hole spanner
20 Clamping ring
21 Clamp screw
22 Button (to turn the main handle) *
23 Lock (to prevent the machine from being
switched on unintentionally, or for continuous
operation)*
24 Trigger (for switching on and off) *
* not in scope of delivery/ depends on equipment

6. Initial Operation

Prior to any conversion work: pull the mains
plug out of the socket. The machine must be
switched off and the spindle at a standstill.
Before commissioning, check that the rated
mains voltage and mains frequency stated on
the type plate match your power supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
Use only extension cables with a minimum cross-
2
section of 1.5 mm . Extension cables must
correspond to the power consumption of the
machine (cf Technical Specifications). If a cable
roller is used, always roll up the cable completely.
6.1 Attachguard at the angle grinder
Dismantle the extraction guard (8) and guide
table (10)
See page 2, fig. A.
1. Loosen clamping nut (3) and swivel extraction
guard (8) upwards.
2. The extraction guard (8) can be removed from
the guide table (10) in the shown position.
Attach the extraction guard (8) to the angle
grinder
See page 2, fig. B.