Bosch 0 607 350 198 Mode D'emploi page 17

OBJ_BUCH-1326-002.book Page 17 Wednesday, August 7, 2013 8:59 AM
Technical Data
Pneumatic Random Orbit Sander
Article number 0 607 350 ...
No-load speed n
0
Stroke
Sanding sheetØ
Max. working pressure for tool
Thread size of hose connection
Inner diameter of hose
Air consumption at no-load
Weight according to EPTA-Procedure 01/2003
Noise/Vibration Information
Measured sound values determined according to EN ISO 15744.
The noise level when working can exceed 80 dB(A). Wear hearing protection!
Typically the A-weighted noise level of the pneumatic tool is:
Sound pressure level L
pA
Uncertainty K
Vibration total values a (triax vector sum) and uncertainty K determined according to EN 28927:
h
a
h
K
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in
EN ISO 11148 and may be used to compare one pneumatic tool with another. It may be used for a preliminary assessment of
exposure.
The declared vibration emission level represents the main applications of the pneumatic tool. However if the pneumatic tool is
used for different applications, with different accessories or is poorly maintained, the vibration emission may differ. This may
significantly increase the exposure level over the total working period.
An exact estimation of the level of exposure to vibration should also take into account the times when the pneumatic tool is
switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total
working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintaining the pneumatic tool
and the accessories, keeping the hands warm, organisation of work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents:
EN ISO 11148 according to the provisions of the directive
2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 08.08.2013
Bosch Power Tools
... 198
-1
min 12000
mm 2.5
mm 80
bar 6.3
psi 91
1/4" NPT
mm 10
l/s 8.3
cfm 17.6
kg 0.6
lbs 1.3
dB(A) 73
dB 3
2
m/s < 2.5
2
m/s 1.5
Assembly
Connecting the Air Supply (see figure A)
 Pay attention that the air pressure is not less than
6.3 bar (91 psi), as the pneumatic tool is designed for
this operating pressure.
For maximum performance, the values for the inner hose di-
ameter as well as the connection threads must be adhered to
as listed in the "Technical Data" Table. To maintain the full
performance, only use hoses with a maximum length of 4 m.
The compressed air supplied should be free of foreign materi-
al and moisture to protect the tool from damage, contamina-
tion, and the formation of rust.
Note: The use of a compressed-air maintenance unit is neces-
sary. This ensures proper function of the pneumatic tools.
Observe the operating instructions of the maintenance unit.
All fittings, connecting lines and hoses must be dimensioned
for the pressure and the required air volume.
English | 17
... 199 ... 200
12000 12000
5.0 2.5
150 150
6.3 6.3
91 91
1/4" NPT 1/4" NPT
10 10
8.5 8.5
18.0 18.0
0.7 0.7
1.5 1.5
76 76
3 3
3.1 3.1
1.5 1.5
3 609 929 C71 | (7.8.13)