Silverline 588812 Mode D'emploi

Wheel Bearing Removal Kit 22pce
FR Kit d'outils de montage et de démontage de roulements, 22 pcs
DE Radlagerwerkzeug mit Zubehör, 22-tlg. Satz
ES Accesorios para instalar y extraer rodamientos de ruedas, 22 pzas
IT Kit di smontaggio dei cuscinetti delle ruote 22 p.zi
NL 22-delige wiellager montageset
PL Zestaw do montażu i demontażu łożysk kół, 22 szt.
Fig.I
18 1-14 17/19/24/22 15/16 21
GB
Product Familiarisation
Specification
Metric Imperial
Drift sizes: OD Nominal OD Nominal
88mm 3.5"
83mm 3.25"
81.5mm 3.2"
77.5mm 3"
75mm 2.95"
73mm 2.88"
73mm 2.88"
71.5mm 2.8"
70mm 2.75"
66.5mm 2.65"
63mm 2.5"
59mm 2.3"
55mm 2.1"
50mm 2"
Metric
Sleeve
OD mm ID mm Width mm OD Imp
sizes
76mm 69mm 65mm 3"
86mm 76mm 65mm 3.4"
91mm 82mm 65mm 3.5"
102mm 92.5mm 65mm 4"
Hub Screw Length: 210mm
Hub Screw Drive: 32, 38mm
As part of our ongoing product development, specifications of Silverline products may alter without notice.
20
Introduction
1. 88mm Drift Ring Thank you for purchasing this Silverline product. This manual contains information necessary for safe and
effective operation of this product. This product has unique features and, even if you are familiar with similar
2. 83mm Drift Ring
products, it is necessary to read this manual carefully to ensure you fully understand the instruction. Ensure
3. 81.5mm Drift Ring
all users of the product read and fully understand this manual.
4. 77.5mm Drift Ring
5. 75mm Drift Ring General Safety
6. 73mm Drift Ring
Carefully read and understand this manual and any label attached to the tool before use. Keep these
7. 73mm Drift Ring
instructions with the product for future reference. Ensure all persons who use this product are fully
acquainted with this manual.
8. 71.5mm Drift Ring
Even when used as prescribed it is not possible to eliminate all residual risk factors. Use with caution. If you
9. 70mm Drift Ring
are at all unsure of the correct and safe manner in which to use this tool, do not attempt to use it.
10. 66.5mm Drift Ring
WARNING: Ensure all workshop practice regulations are adhered to whilst using this tool
11. 63mm Drift Ring
WARNING: Familiarise yourself with this kit before use.
12. 59mm Drift Ring
DO NOT use this tool while under the influence of alcohol, drugs or any intoxicating medication or tired.
13. 55mm Drift Ring
IMPORTANT: ALWAYS refer to the vehicle manufacturer's specification and instruction for the correct
14. 50mm Drift Ring
procedure and information for the specific vehicle you are working on. The instructions given in this manual
15. Sleeve Cap (Ø 102mm)
is given as a guide only.
16. Sleeve Cap (Ø 86mm)
Intended Use
17. Sleeve (Ø 102mm)
18. Thrust Nut
Wheel bearing removal kit for fast, effective removal and installation of wheel bearings on front wheel
19. Sleeve (Ø 91mm)
drive vehicles.
20. Thrust Bolt
Unpacking Your Tool
21. Washer
22. Sleeve (Ø 76mm)
• Carefully unpack and inspect your new tool. Familiarise yourself with all its features and functions
23. Workshop Press Adaptor
• Ensure that all parts of the tool are present and in good condition. If any parts are missing or damaged,
have such parts replaced before attempting to use this tool
24. Sleeve (Ø 86mm)
Before Use
• Inspect the general condition of the vehicle, checking for any hazards that may interfere with the use of
this tool
Imperial
• DO NOT use damaged equipment
• Identify the correct tool components to be used for the task at hand
ID Imp Width Imp
Operation
2.9" 2.5"
WARNING: ALWAYS wear eye protection as well as suitable gloves when working with this tool.
3" 2.5"
Bearing removal & installation
Bearing removal
3.2" 2.5"
• Select the correct Sleeve size (17, 19, 22 or 24) to sit on the outside of the bearing housing with the
3.6" 2.5"
correct Sleeve Cap (15 or 16), and the correct sized Drift (1-14) for driving the bearing from the housing
• Assemble the kit through the bearing (see Fig. I)
• Secure the end of the Thrust Bolt (20) and tighten the Thrust Nut (18) simultaneously to remove the
bearing
• Keep the Thrust Nut and Thrust Bolt well lubricated before and during the bearing removal process
5 7
4 6 8
1
3
2
24
23
22 21
Fig.II
20 21 15-16
9 11 13
10 12 14
15
16
17
18
20 19
1-14 18
Bearing installation
• Select the correct Sleeve Cap (15 or 16) to sit on the outside of the bearing housing and the correct Drift
(1-14) to drive the new bearing into position
• Assemble the kit through the bearing (see Fig. II)
• Secure the end of the Thrust Bolt (20) and tighten the Thrust Nut (18) simultaneously to install the
bearing.
• Keep the Thrust Nut and Thrust Bolt well lubricated before and during the bearing installation process.
WARNING: ensure bearing is positioned in the housing correctly according to vehicle manufacturers'
specification before use. Failure to do so may result in serious personal injury or harm to others.
Accessories
• A range of accessories, safety equipment and consumables is available from your Silverline stockist
• Spare parts can be obtained from toolsparesonline.com
Maintenance
General inspection
• Keep the parts in this kit clean. Use a clean cloth and mild detergent if necessary
• Dirt and dust will cause parts to wear quickly and shorten the service life of the product
Lubrication
• Lubricate all moving parts at regular intervals with a suitable grease or spray lubricant
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: silverlinetools.com/en-GB/Support
Address:
Powerbox
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
• Tools may contain traces of tool oil, other lubricants and pollutants. Therefore, tools should not be
disposed of with household waste
• Contact your local waste disposal authority for information on the correct way to dispose of this tool
silverlinetools.com
588812
GARANTIE À VIE
UNBEGRENZTE GARANTIE
GARANTÍA DE POR VIDA
GARANZIA A VITA
LEVENSLANGE GARANTIE
GWARANCJA DOŻYWOTNIA
Version date: 24.08.2017