Additional Information; Troubleshooting - Pioneer ELITE N-50 Mode D'emploi

Additional information

Chapter 10:
Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with
this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other
components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks
listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
• If the unit does not operate normally due to external effects such as static electricity disconnect the power plug
from the outlet and insert again to return to normal operating conditions.
General problem
Problem Check
The power does not turn When Quick Start Mode is set to
on. On, if the power cord is
disconnected, the next time the
power cord is connected the unit will
not respond for about one minute.
Long time required before In its factory default status, the unit
power is supplied. requires about 20 seconds before
power is supplied.
The unit automatically Is Auto Power Off set to On?
turns off.
The unit suddenly This unit may have a serious
switches off and the problem. Do not try switching the
STANDBY indicator unit on.
blinks.
Settings you have made Did you suddenly turn off the power? Be sure to press  STANDBY/ON on the remote control,
have been cleared.
Difference in volume This is not a problem with this unit.
between MP3, WMA and
iPod/iPhone/iPad.
This unit cannot be Are you operating from far away?
operated with the remote
control.
Is the remote control sensor exposed
to direct sunlight or strong artificial
light from a fluorescent bulb, etc.?
Are the batteries dead?
Remedy
Wait at least one minute, then press /I STANDBY/ON on
the front panel.
To shorten the time required until power is supplied, change
the Power Off Setting so as to turn Quick Start Mode
On. However, when Quick Start Mode is On, power
consumption during STANDBY mode will increase
(page 20).
Change the setting of Auto Power Off to Off (page 20).
Disconnect from the power and call a Pioneer authorized
independent service company.
then press /I STANDBY/ON on the front panel and wait
for the STANDBY indicator on the front panel display to turn
off before unplugging the power cord.
The volume may sound differently depending on the input
source and recording format.
Operate from within a distance of Operate within 7 m (23 ft.),
30° of the remote sensor on the front panel (page 5).
The remote control signals may not be received properly if
the remote control sensor is exposed to direct sunlight or
strong artificial light from a fluorescent bulb, etc.
Replace the batteries (page 5).
When an iPod/iPhone/iPad is connected
Problem Check
Can't operate the iPod/
iPhone/iPad.
Sound not produced from Is sound being produced from the
iPod/iPhone/iPad. speaker of the iPod/iPhone/iPad?
Power is not supplied to Does an error message appear in the
the Pod/iPhone/iPad. front panel display?
No power is supplied if the power
consumption is too high.
When an Bluetooth adapter is connected
Problem Check
The Bluetooth wireless Check that no object that emits
technology device cannot electromagnetic waves in the 2.4 GHz
be connected or operated. band (microwave oven, wireless LAN
Sound from the Bluetooth device or Bluetooth wireless
wireless technology technology apparatus) is near the
device is not emitted or unit.
the sound is interrupted.
Check that the Bluetooth wireless
technology device is not too far from
the unit and that obstructions are not
set between the Bluetooth wireless
technology device and the unit.
The Bluetooth wireless technology
device may not be set to the
communication mode supporting the
Bluetooth wireless technology.
Check that pairing is correct.
Check that the profile is correct.
BT Error 5 is displayed The Bluetooth adapter may be
and the unit cannot be damaged.
operated.
Remedy
Make sure the iPod/iPhone/iPad is connected correctly
(refer to iPod/iPhone/iPad playback on page 11).
Also, try disconnecting the iPod/iPhone/iPad then
reconnecting it.
If the iPod/iPhone/iPad is experiencing a hangup, try
resetting the iPod/iPhone/iPad, and reconnect it to the unit.
Disconnect power to the unit, then turn on again. After
setting for iPod input, connect the iPod/iPhone/iPad.
Turn the power off then back on.
Turn the power off, then disconnect and reconnect the iPod/
iPhone/iPad.
Remedy
If such an object is near the unit, set the unit far from it. Or,
stop using the object emitting the electromagnetic waves.
Set the Bluetooth wireless technology device and the unit so
that the distance between them is less than about 10 m and
no obstructions exist between them.
Check the setting of the Bluetooth wireless technology
device.
The pairing setting was deleted from this unit or the
Bluetooth wireless technology device. Reset the pairing.
Use a Bluetooth wireless technology device that supports
A2DP profile and AVRCP profile.
Turn the unit's power off, disconnect the Bluetooth adapter,
then try turning the power on again. If the symptom is
corrected, the Bluetooth adapter may have been damaged
and should be serviced.
10
21
En