Publicité
ENGLISH
A. SPECIFICATIONS
• Programmable with a smartphone
or tablet through Rain Bird Apps
• Communication with the Rain Bird App
with Bluetooth 4.0 technology.
• Operates with the RAIN BIRD TBOS
latching solenoid.
• 3 independent programs (A, B, C) with up
to 8 start times per day and per program.
Stations can be assigned to several
programs with different watering run time.
• Watering time from 1 minute to 12 hours
per station.
• Watering cycle: customized cycle
(7 days), even, odd, odd-31 (no watering
on 31), cyclical.
• Manual watering capabilities.
• Program level and global Monthly
Seasonal Adjust (0 to 300%).
• Rain Delay (1 to 14 days).
• Watering programs backup.
• Station names capabilities.
• Master Valve connection (not available
on 1-station module).
• Sensor connection (Rain sensor or Flow
sensor).
• Option: Radio connection with addition
of a TBOS-II Radio Adaptor.
• Operating temperature range: 14°F
to 149°F.
• Operating pressure: up to 10 Bars.
B. 9V BATTERY INSTALLATION
(not included)
See diagram 1.1
• Powered by a new 9V alkaline battery
type 6AM6 (international standard) or
6LR61 '(European standard)
• Low battery icon displays on the Rain
Bird App.
C. SOLENOID INSTALLATION
See diagrams 1.3
Mounting the solenoid on the valve: remove
the existing solenoid on the valve and
replace it with the latching solenoid. Gently
screw it hand-tight.
1. Connect the latching solenoid to the
control module. Use the Rain Bird wire
connectors supplied with the module.
Important : the wire run between the control
module and the solenoid must not exceed
10 m using 0.75 mm² wire.
Check the system by using the manual
start function. If the system does not
turn on, screw the solenoid a little tighter
to the valve.
D. MAINTENANCE
• Replace the 9V battery (alkaline : type
6LR61 or equivalent) once a year.
• If you connect a transmitter to the control
module in infrared mode, make sure that
the optical connector is clean when the
connection is made. Use water to clean
it if needed.
FCC STATEMENT
Caution: the user that changes or
modifications not expressly approved by
the party responsible for compliance could
void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instruction, may cause harmful interference
to radio communications. However, there
is no guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful interference
to radio or television reception which can
be determined by turning the equipment
off and on, the user is encouraged to try
to correct interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet
on circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
This device complies with FCC RF radiation
exposure limits set forth for general
population. This device must be installed
to provide a separation distance of at least
20cm from all persons and must not be co-
located or operating in conjunction with any
other antenna or transmitter.
IC STATEMENT
This class (B) digital apparatus complies with
Canadian ICES-003.
Under Industry Canada regulations, this
radio transmitter may only operate using
an antenna of a type and maximum (or
lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio
interference to other users, the antenna
type and its gain should be so chosen that
the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for
successful communication.
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation
is subject to the following two conditions:
(1) this device may not cause interference,
and (2) this device must accept any
interference, including interference
that may cause undesired operation
of the device.
This device complies with Industrie Canada
RF radiation exposure limits set forth for
general population. This device must be
installed to provide a separation distance
of at least 20cm from all persons and
must not be co-located or operating in
conjunction with any other antenna or
transmitter.
Publicité
