Service; Safety Messages; Introduction - GBC AdvancedPunch Manuel D'utilisation

Safety messages

MAIN CORDSET SELECTION
(THE FOLLOWING NOTE ONLY APPLIES ONLY TO THE UNITS
RATED 230V 50HZ, AND LOCATED IN THE EUROPEAN UNION)
CAUTION: WHEN CHOOSING A DETACHABLE LINE
CORD FOR USE WITH YOUR ADVANCEDPUNCH,
ALWAYS FOLLOW THE FOLLOWING PRECAUTIONS
The cordset consists of three parts: the attachment plug, the cord and
the appliance inlet. Each of these components must have European
regulatory safety approvals.
The following minimum electrical ratings for the specific cordset are
published for safety purposes.
DO NOT USE CORDSETS THAT DO NOT MEET THE FOLLOWING
MINIMUM ELECTRICAL REQUIREMENTS.
PLUG: 3 amperes, 250 volts, 50/60 Hz, Class 1, 3 conductor, European
safety approved.
CORD: Type H05VV-F3G0.75, Harmonized (< HAR>). The "< >"
symbols indicate cord approved according to appropriate European
standard (NOTE: "HAR" may be substituted for approval mark of
European safety agency that approved the cord. An example would be
"< VDE >").
APPLIANCE CONNECTOR: 3 amperes, 250 volts, 50/60 Hz, European
safety approved, Type IEC 320. The cordset shall not exceed 3 meters
in length. A cordset with component electrical ratings greater than the
minimum specified electrical ratings may be substituted.
Service, AdvancedPunch
Do not attempt to service your AdvancedPunch yourself. Contact an
authorized service representative for any required repairs or major
maintenance for your AdvancedPunch.
DO NOT REMOVE THE MACHINE'S COVER.
There are NO user-serviceable parts inside the machine in order to
avoid potential personal injury and/or damage to property or the machine
itself.
Service, Diesets
Every dieset is thoroughly oiled at the factory prior to shipping. During
normal use this oil will be exhausted and should be replaced. As part
of regular maintenance, each dieset should be oiled after approximately
50K punch cycles. GBC recommends use of brand 3-IN-ONE oil as it
is readily available. Other light machine oils can also be used.
To oil the dieset, simply apply a small bead of oil along the entire
length of the felt strip that is located on the dieset. After oil has been
applied, re-install the dieset into the AdvancedPunch and run a small
test print job. Please note that it is normal for oil to be present on the
first set of sheets punched after oiling the dieset. After approximately
25 to 50 sheets oil will no longer be found on the punched sheet. At
this time the AdvancedPunch can be utilized for punching of print jobs.
Safety messages
FCC NOTE
(THE FOLLOWING NOTE ONLY APPLIES TO THE UNITS RATED
115V 60HZ.)
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the Operation
Manual, may cause harmful interference with radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct
the interference at his/her own expense.
CAUTION: CHANGES OR MODIFICATIONS NOT
EXPRESSLY APPROVED BY GENERAL BINDING
CORPORATION COULD VOID YOUR AUTHORITY TO
OPERATE THE EQUIPMENT.
Canada Class A Notice - Avis Canada, Classe A
This Class A digital apparatus complies with Canadian ICES-3.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.

2. INTRODUCTION

Thank you for purchasing the AdvancedPunch. It is a versatile
production system that will enable you to punch documents for a variety
of binding styles by means of a simple die change. It has also been
designed for easy operation.
The AdvancedPunch is an innovative solution for punching paper and
offers the following design features:
Quick-change die sets that are self-latching without tools or levers.
All AdvancedPunch die sets include an Identification Label providing
the user with the hole pattern and name.
Convenient storage area for three extra Die Sets located above the
sheet bypass.
4
AdvancedPunch
GB