STEINEL LN 710 LED Mode D'emploi page 6

GB
1. About this document
Please read carefully and keep in a safe place.
– Under copyright. Reproduction either in whole or
in part only with our consent.
– Subject to change in the interest of technical
progress.
Symbols
!
Hazard warning!
Reference to other information in the
...
document.
2. General safety precautions
Disconnect the power supply before
!
attempting any work on the unit.
• During installation, the electric power cable being
connected must not be live. Therefore, switch off
the power first and use a voltage tester to make
sure the wiring is off-circuit.
• Installing these units involves work on the mains
voltage supply; installation must therefore be
carried out professionally in accordance with the
applicable national wiring regulations and electri-
cal operating conditions (e.g.: DE-VDE 0100,
AT-ÖVE/ÖNORM E 8001-1, CH-SEV 1000).
• Only use genuine replacement parts.
• Repairs may only be made by specialist work-
shops.
3. LN 710 LED
Proper use
– LED light with Nightmatic function for indoor and
outdoor wall mounting.
Measures ambient brightness and automatically
switches the light ON at dusk and automatically
switches it OFF again in line with various setting
options.
Package contents (Fig. 3.1)
– Luminaire
– Wall mount
– two screws
– two wall plugs
– Three spacers
Product dimensions (Fig. 3.2)
Product components (Fig. 3.3)
A Sealing plug
B Wall mount
C Connecting terminal
D Luminaire enclosure
Retaining strap
E
F ON/OFF in the morning
G Twilight setting
H Night economy mode
4. Electrical connection
Wiring diagram (Fig. 4.1)
The supply lead is a three-core cable:
L = phase conductor (usually black, brown or
grey)
N = neutral conductor (usually blue)
PE = protective-earth conductor (green/yellow)
If you are in any doubt, identify the conductors
using a voltage tester; then disconnect from the
power supply again. Connect phase (L) and neutral
conductor (N) to the connecting terminal; optionally,
protective-earth conductor (PE) can be connected
to terminal (E).
Important:
incorrectly wired connections will produce a short
circuit later on in the product or fuse box. In this
case, you must identify the individual conductors
once again and reconnect them. A mains switch for
switching the product ON and OFF may, of course,
be installed in the mains supply lead. The light
source of this luminaire cannot be replaced. If the
light source needs to be replaced (e.g. at the end
of its service life), the complete luminaire must be
replaced.
5. Mounting
• Check all components for damage.
• Do not use the product if it is damaged.
• When installing the LED luminaire, make sure the
installation site is not subject to vibration.
Mounting procedure
• Switch OFF power supply (Fig. 4.1)
• Undo screws (Fig. 5.1)
• Press catch and pull luminaire off the wall mount
(Fig. 5.2)
• Undo retaining strap and terminal and remove
luminaire (Fig. 5.3)
• Mark drill holes (Fig. 5.4)
• Drill holes and insert wall plugs (Fig. 5.5)
– 10 –
• Pierce sealing plug for power supply lead
(Fig. 5.6)
• Concealed mounting (Fig. 5.7)
• Surface mounting (Fig. 5.8)
• Attach retaining strap and terminal to the wall
mount (Fig. 5.9)
• Connect conductors (Fig. 5.10)
• Remove retaining strap on lamp side and store in
wall mount (Fig. 5.11)
• Install luminaire enclosure on wall mount (Fig. 5.12)
• Tighten screws (Fig. 5.13)
• Switch ON power supply (Fig. 5.13)
• Make settings ➜ "6. Function"
6. Function
Factory settings
Twilight level: 2000 lux
Night economy mode: Off
ON/OFF in the morning: ON
Twilight setting (Fig. 6.1 G)
The chosen response threshold can be infinitely
varied from approx. 2 to 2000 lux.
– Control dial set to = daylight mode
(depending on ambient brightness)
– Control dial set to = twilight mode
(approx. 2 lux)
Night economy mode (Fig. 6.1 H)
The luminaire can be switched OFF automatically at
night to save even more electricity. The electronic
system does not have a clock. All times are com-
puted by the microprocessor on the basis of light
levels at twilight. Seasonal changes in light levels are
identified automatically and taken into account.
When selected, the night economy mode can be
infinitely varied from 0 to 7 hours.
– Control dial set to Off = luminaire ON all night
– Control dial set to ECO = luminaire OFF for
3.5 hours in the night
– Control dial set to ECO+ = light OFF for 7 hours
in the night
ON/OFF in the morning (Fig. 6.1 F)
The night economy mode always ends in the early
hours of the morning between approx. 4 and 5
a.m. After then, the luminaire switches ON again
automatically when it gets dark.
– Control dial set to On = light switches ON auto-
matically at dawn
– Control dial set to Off = light stays OFF in the
morning
7. Maintenance
The product requires no maintenance.
The luminaire can be cleaned with a damp cloth
(without detergents) if dirty.
8. Disposal
Electrical and electronic equipment, accessories
and packaging must be recycled in an environmen-
tally compatible manner.
Do not dispose of electrical and electronic
equipment as domestic waste.
EU countries only:
Under the current European Directive on Waste
Electrical and Electronic Equipment and its imple-
mentation in national law, electrical and electronic
equipment no longer suitable for use must be col-
lected separately and recycled in an environmentally
compatible manner.
9. Manufacturer's Warranty
As purchaser, you are entitled to your statutory
rights against the vendor. If these rights exist in your
country, they are neither curtailed nor restricted by
our Warranty Declaration. We guarantee that your
STEINEL Professional sensor product will remain
in perfect condition and proper working order for a
period of 5 years. We guarantee that this product
is free from material-, manufacturing- and design
flaws. In addition, we guarantee that all electronic
components and cables function in the proper man-
ner and that all materials used and their surfaces are
without defects.
Making Claims
If you wish to make a claim, please send your
product complete and carriage paid with the original
receipt of purchase, which must show the date of
purchase and product designation, either to your
retailer or contact us at STEINEL (UK) Limited,
25 Manasty Road, Axis Park, Orton Southgate,
Peterborough, PE2 6UP, for a returns number.
For this reason, we recommend that you keep your
receipt of purchase in a safe place until the warranty
period expires. STEINEL shall assume no liability for
the costs or risks involved in returning a product.
For information on making claims under the terms of
the warranty, please go to
www.steinel-professional.de/garantie
– 11 –