Cleaning The Hygienic Exhaust Filter; Spare Parts And Accessories; Recommendation; Before You Send In The Appliance - Dirt Devil Lifty PLUS Swirl Y05 Mode D'emploi

5 Maintenance

5.3 Cleaning the hygienic exhaust filter

13
14

5.4 Spare parts and accessories

ATTENTION:
Only use original spare parts from the scope of delivery or those that you
have acquired by reordering.
Ordering address: page 48, „International Service"
Further information is available at:

5.5 Recommendation

We recommend:
Swirl Y05 dust filter bags with MicroPor filtration
Swirl , MicroPor and "Y05" are registered trade marks of a company of the Melitta group and used with their permission.

5.6 Before you send in the appliance

WARNING:
Danger of injury! Never use a defective appliance! Always switch off the
appliance and disconnect
troubleshooting chapter 4.3, „Switching off".
Before contacting your authorised Royal dealer, Royal service partner or
appliance market or sending in the appliance, first follow the procedure in
the following table to check if you can solve the problem yourself.
Problem Possible cause / solution
The appli- The socket does not carry current.
ance will not Test the vacuum cleaner at another socket which you are
start. sure carries current.
Power cord is damaged.
Have the power cord replaced by Royal Appliance Cus-
tomer Service, address,
Service".
The dust filter The dust filter bag is full.
bag changing Change the dust filter bag
indicator ap- dust filter bag".
pears in the
Nozzle, telescopic tube or suction hose are blocked.
viewing win-
Remove the obstacle. If necessary, use a long wooden
dow.
stick (e.g. a broomstick) to do this.
The filter is dirty. Clean the respective filter
„Cleaning the motor protection filter" or
„Cleaning the hygienic exhaust filter"
A B
A B
www.dirtdevil.de
it from the mains before
page 48, „International
chapter 5.1, „Changing the
chapter 5.2,
chapter 5.3,
1. Switch off the appliance,
2. Push down the release catch of the exhaust filter cover and fold down
the cover (Fig. 13/A).
3. Pull the hygienic exhaust filter up out of its holder (Fig. 13/B) and tap
the dirt from it over a dust bin.
4. Should this be insufficient, remove the dirt from the filter with a soft
brush, e.g. the furniture brush supplied with the appliance.
5. If such dry cleaning is insufficient, thoroughly rinse the filter by hand in
running clear cold or hand-warm water.
ATTENTION:
The filters are washable, but not suitable for cleaning in washing
machines or dishwashers. Do not use chemical cleansers to clean the
filter. Leave the filters to dry after cleaning them with water
(approx. 24 hours at room temperature). Only put them back into the
appliance when they are completely dry.
6. If the filter is damaged or deformed, replace it (ordering information
chapter 5.4, „Spare parts and accessories").
7. Place the clean/new exhaust filter back into its fitting (Fig. 14/A).
8. Fit the exhaust filter cover on the rear side first and then push it down
on the front side (Fig. 14/B).
Item no.
7010022
Set of 5 dust filter bags and 1 motor protection filter
7019002
1 hygienic exhaust filter
M203
1 parquet brush
M209
1 turbo brush
NOTE:
Insert the bag in direction "A."
Problem
The vacuum The overheating protection has tripped (possibly due to
cleaner stops blocked suction channels, filters, or similar). Switch the
starting
suddenly. appliance off and pull the plug out of the socket. Remove
the cause of overheating (e.g. by disassembling telescop-
ic tube and suction hose and removing the obstacle and/
or cleaning filters). Wait for about 45 minutes. After the
appliance has cooled off, you may switch it on again.
The cleaning The bypass vent (Fig. 1/22) is open.Close the bypass
results are vent (Fig. 1/22).
unsatisfacto-
The attached nozzle is unsuitable. Change the nozzle,
ry in spite of
chapter 3.2, „Selecting the proper nozzle"
the appli-
The position of the "carpet/hard floor" selector (Fig. 1/2) is
ance work-
unsuitable. Set the "carpet/hard floor" selector (Fig. 1/2)
ing correctly.
to the correct position for the type of floor,
„Vacuum cleaning", step 4.
The dust filter bag is full. Change the dust filter bag
chapter 5.1, „Changing the dust filter bag".
The filter is dirty. Clean the respective filter
„Cleaning the motor protection filter" or
„Cleaning the hygienic exhaust filter"
Nozzle, telescopic tube or suction hose are blocked.
Remove the obstacle. If necessary, use a long wooden
stick (e.g. a broomstick) to do this.
chapter 4.3, „Switching off"
Description
Possible cause / solution
chapter 4.2,
chapter 5.2,
chapter 5.3,
15