Using Hdmi Input; Connecting Hdmi Equipment - Pioneer PDP-506FDE Mode D'emploi

Enjoying through External Equipment

Using HDMI Input

The INPUT 3 terminals include HDMI terminals to which digital
video and audio signals can be input. To use the HDMI
terminal, activate the terminal and specify the types of video
and audio signals to be received from the connected
equipment. For the types of these signals, see the operation
manual that came with the connected equipment.
Before starting the menu, press INPUT 3 on the remote control
unit or press INPUT on the Media Receiver to select INPUT 3.
Input signal correlation table
1920∗1080i@50Hz
720∗576p@50Hz
1280∗720p@50Hz
720(1440)∗576i@50Hz
1920∗1080i@59.94/60Hz
720∗480p@59.94/60Hz
1280∗720p@59.94/60Hz
720(1440)∗480i@59.94/60Hz
1920∗1080p@24Hz
For audio, the system supports the following:
• Linear PCM (STEREO 2ch)
• Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz

Connecting HDMI equipment

Media Receiver (rear view)
SERVICE ONLY
INPUT 1
ANT I /o link.A
SELECT
INPUT
2 3
INPUT 2
SCART cable
(commercially available.)
Connect the SCART cable only
when inputting analogue audio
signals.
HDMI equipment
To activate the HDMI terminal:
1
Press HOME MENU.
2
then ENTER).
Select "Option" ( /
3
Select "HDMI Input" ( /
4
then ENTER).
Select "Setting" ( /
5
then ENTER).
Select "Enable" ( /
INPUT 2
Y P P R -AUDIO -L
B R
COMPONENT VIDEO AUDIO OUTPUT
INPUT 3
HDMI BLACK
SYSTEM CABLE
HDMI cable
(commercially
available.)
then ENTER).
Item
Disable
(factory default)
Enable
6
Press HOME MENU to exit the menu.
To specify the type of digital video signals:
1
Repeat steps 1 to 3 provided for "To activate the HDMI
terminal".
2
Select "Video" ( /
3
Select the type of digital video signals ( /
• If you select "Auto", an attempt will be made to identify
the type of digital video signals when digital video
signals are received.
Item
Auto
(factory default)
Colour-1
Colour-2
Colour-3
4
Press HOME MENU to exit the menu.
NOTE
• If you select a parameter other than "Auto", make such a
setting that results in natural colour.
• If no image appears, specify another digital video signal type.
• For the digital video signal types to be specified, check the
operation manual that came with the connected equipment.
To specify the type of audio signals:
WHITE
1
Repeat steps 1 to 3 provided for "To activate the HDMI
terminal".
2
Select "Audio" ( /
3
Select the type of audio signals ( /
• If you select "Auto", an attempt will be made to identify
the type of audio signals when audio signals are
received.
Item
Auto
(factory default)
Digital
Analogue
4
Press HOME MENU to exit the menu.
NOTE
• If no sound is output, specify another audio signal type.
• For the audio signal types to be specified, check the
operation manual that came with the connected equipment.
• Depending on the equipment to be connected, you also need
to connect analogue audio cables.
Description
Deactivates the HDMI terminal.
Activates the HDMI terminal.
then ENTER).
then ENTER).
Description
Automatically identifies input digital video
signals.
Digital Component Video signals (4:2:2) locked
Digital Component Video signals (4:4:4) locked
Digital RGB signals locked
then ENTER).
then ENTER).
Description
Automatically identifies input audio signals.
Accepts digital audio signals.
Accepts analogue audio signals.
10
41
En